Lighthouse Worldwide Solutions ApexR02 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 84

background image

00

248083447-1 Rev 1

5-1

5

Maintenance
Procedures

Introduction

This chapter provides routine maintenance instructions that the

Apex

Remote

instrument require.

The maintenance procedures described in this chapter are not required
on regular or prescribed intervals and should be performed only if the
user has reason to question the data they are receiving.

Safety

Before performing any of the maintenance tasks described in this
chapter, read Chapter 1 of this manual and become familiar with the
warnings and caution labels.

Maintenance

Calibration

To maintain optimum performance of this instrument, it should be
recalibrated annually by a Lighthouse Authorized Service Provider.

Zero Count
Test

This section will provide the user a procedure to determine if the

Apex

Remote

can successfuly complete several zero counts. A purge

filter must be attached to the instrument and six (6) five (5) minute
samples must be taken. There should be no more than 1 count on
average per five-minute sample.
1.

Connect the Purge filter to the sample inlet.

2.

Apply power to the instrument.

3.

Configure the unit to sample for 30 minutes.

4.

Allow the instrument to sample through a 30-minute period. This
time allows the unit to warm up and purge any residual particles
that might be inside it.

5.

Configure the unit to sample for 5 minutes with a 10-second hold.

6.

Allow the instrument to take 6 samples.

7.

If an average of more than one count per five-minute period is
reported, allow the instrument to sample for 30 minutes to purge
it, then repeat the test (Steps 5 & 6).

«
...
39
40
41
42
43
...
»

Содержание ApexR02





















































































Отзывы:

Нет отзывов

Похожие инструкции для ApexR02

Бренд: ABB Страницы: 20

Бренд: Utilitech Страницы: 2

Бренд: Keithley Страницы: 48

Бренд: BANTE inststruments Страницы: 15

Бренд: 3Bays Страницы: 21

Бренд: MadMan Страницы: 37

Бренд: MADDALENA Страницы: 5

Бренд: Magnum Energy Страницы: 3

Kotron 805 series

Бренд: Magnetrol Страницы: 36

Бренд: Magnescale Страницы: 104

Бренд: Magnescale Страницы: 44

Бренд: WalkLAB Страницы: 16

Бренд: SOMFY Страницы: 40

Arrow Mobile Android

Бренд: MADDALENA Страницы: 12

Бренд: Ocean Reef Страницы: 24

Бренд: Suaoki Страницы: 79

Бренд: dacell Страницы: 39

Бренд: Fungilab Страницы: 47

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды