LGMG MT86H Скачать руководство пользователя страница 6

Страница: 6 / 165

MT86H

Operation

and

Maintenance

Manual

Foreword

Thanks for choosing mining dump trucks manufactured by Lingong Group Jinan Heavy

Machinery CO., LTD., Ltd. This manual describes the mechanism, driving and operating,

maintenance and adjustment, technical parameters and service/adjustment data of the MT86H series

mining dump trucks.

Maximizing the profits from your Off-Highway Dump Truck is our common goal, which is to a

large extent dependent on your familiarity with the truck and a careful and thorough maintenance.

We sincerely hope that you can read through the manual prior to the first start, operation as

well as maintenance and service of the truck and get full understanding of the operations and

maintenances described herein.

All the pictures and descriptions covered herein are correct at time of publication; but

the structures and performances of our products are constantly improved and perfected; therefore,

please understand that the related design, operation and maintenance instructions are subject

to change at any time without prior notice. For the latest information on the dump truck or in

case of any doubts about this manual, please consult LGMG.

This manual is applicable for MT 86H series Off-Highway Dump Truck (standard configuration).

Users shall be in strict accordance with the mileage or time interval in the maintenance schedule

to do maintenance to the assembly and the dump truck.

The manual is a part of the dump truck and thus shall be handed over together when transferring

the ownership or the right of the truck. If the manual is lost, damaged or hard to be recognized,

please replace it in time.

The copyright of this manual is reserved by Lingong Group Jinan Heavy Machinery CO.,

LTD., Ltd. Reproduction or reprinting without written permission by LGMG is prohibited.

Содержание MT86H






































































































































































Результаты поиска

Содержание MT86H

Отзывы:

Похожие инструкции для MT86H

Бренды по названию

Популярные бренды

LGMG MT86H, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание MT86H

Отзывы:

Похожие инструкции для MT86H

Бренды по названию

Популярные бренды