LGMG MT86H Скачать руководство пользователя страница 55

Страница: 55 / 165

MT86H

Operation

and

Maintenance

Manual

The drive axle of MT86 mining dump truck is

equipped with bogie differential lock. When

the wheel slips or gets stuck in the mud, the

bogie differential lock can lock the bogie

differential between the intermediate axle and

the rear axle, thus increasing the vehicle

trafficability.

1) Connection of bogie differential lock: Only

when the vehicle is parked or travels straight

at a low speed (equivalent to walking speed)

can the differential lock be engaged.

Press down the bogie differential rocker

switch. When the bogie differential is engaged,

the bogie differential indicator on the

instrument panel will be on.

△

WARNING: When the vehicle is

running, always release the clutch

before the connection of bogie

differential lock!

2) Disengagement of bogie differential lock:

Release the accelerator, depress the clutch,

and pull up the bogie differential rocker

switch. When the bogie differential is

disconnected, the bogie differential

indicator on the instrument panel will be off.

Содержание MT86H






































































































































































Результаты поиска

Содержание MT86H

Отзывы:

Похожие инструкции для MT86H

Бренды по названию

Популярные бренды

LGMG MT86H, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание MT86H

Отзывы:

Похожие инструкции для MT86H

Бренды по названию

Популярные бренды