LGMG MT86H Скачать руководство пользователя страница 68

Страница: 68 / 165

MT86H

Operation

and

Maintenance

Manual

loose.

6) Check the oil pressure and water temperature

of the diesel engine.

7) Check if the exhaust temperature, color,

sound and vibration are normal, and the speed

is stable.

Refer to "Periodic Inspection and Technical

Maintenance of Diesel Engine" section of

Operation and Maintenance Instruction of WD12

Engine for details.

4.1.4

Maintenance

MT86 engine shall be inspected and maintained

at interval specified in “5.1 Interval

Mileage of Routine Inspection and

Maintenance”. Refer to "Periodic Inspection

and Technical Maintenance of Diesel Engine"

section of Operation and Maintenance

Instruction of WD12 Engine for details.

4.2 Operation and maintenance of intake
system

The working component of the intake system is

the three-stage desert filter, which consists

of the cyclonic prefilter, coarse filter and

fine filter.

Содержание MT86H






































































































































































Результаты поиска

Содержание MT86H

Отзывы:

Бренды по названию

Популярные бренды

LGMG MT86H, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание MT86H

Отзывы:

Бренды по названию

Популярные бренды