LGMG MT86H Скачать руководство пользователя страница 94

Страница: 94 / 165

MT86H

Operation

and

Maintenance

Manual

before 5,000 kilometers (or within 1 month).

The first maintenance items are listed as

follows:

① Refill grease to the grease nozzle of the

master pin, the camshaft support and the

regulating arm as required. If it is difficult

to refill grease, check it immediately and stop

operating;

② Check if the connecting bolts between

components outside the axle are loose and

fasten them;

③ Check and regulate the brake clearance,

which shall be between 0.7mm and 1.2 mm;

c. Periodic maintenance

The periodic maintenance shall be carried out

every 20,000 km or 1 year after the first

maintenance. The periodic maintenance items

are listed as follows:

Repeat the first maintenance items;

Lubricate the brake shoe pin and the brake

roller;

Check the friction plate wear degree. The

thickness of the friction plate shall not be

less than 8mm. Replace it if it is less than

8mm.

△

Note: When performing inspection

Содержание MT86H






































































































































































Результаты поиска

Содержание MT86H

Отзывы:

Бренды по названию

Популярные бренды

LGMG MT86H, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание MT86H

Отзывы:

Бренды по названию

Популярные бренды