background image

MS- E10 User Guide 

                                     

Due to our policy of continuous product innovation, some specifications may change without notification. 

                 ©LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. “LG” is a registered trademark of LG Corp.         60 

  

Update device application 

Provisioned templates can be updated at some later time using the Upgrade Template job step. Multiple Upgrade Template 

steps can be included in a single provisioning prototype to upgrade multiple templates at the same time. 
Prerequisites: 
Step 1  Click the Copy Template button to copy the upgraded .ntpl file to the Supervisor station. 
Step 2  Set up a provisioning prototype to include the Upgrade Template job step and the stations to be updated. 
Step 3  Save and Run the prototype to apply the upgraded template. 
The results will be the same as if you upgraded each template individually with each station's Template Manager. 

Note:  

Initial configurations on the template will be re-applied to the upgraded template. 

 

 

 

Содержание niagara4 MultiSITE Edge 10










































































Отзывы: