LG niagara4 MultiSITE Edge 10 Скачать руководство пользователя страница 63

Страница: 63 / 73

MS- E10 User Guide

Due to our policy of continuous product innovation, some specifications may change without notification.

The figure with numbered call-outs, shown here, indicates the position of USB port and pushbutton

switches.

Figure 38: Position of USB port and pushbutton switches

STAT LED

Status LED, illuminated while controller is powered.

BEAT LED

Heartbeat LED, normally 5Hz, 50% duty cycle. Fast blink during boot process.

DEBUG

Micro-A USB port for serial debug communications

FACTORY RESET

Push-button switch to initiate a return to factory default settings

RESET

Unlabeled push-button switch (located in the recessed cavity) to initiate physical reset of the device.

Содержание niagara4 MultiSITE Edge 10










































































Результаты поиска

Содержание niagara4 MultiSITE Edge 10

Отзывы:

Похожие инструкции для niagara4 MultiSITE Edge 10

Бренды по названию

Популярные бренды

LG niagara4 MultiSITE Edge 10, Руководство пользователя

Результаты поиска

Содержание niagara4 MultiSITE Edge 10

Отзывы:

Похожие инструкции для niagara4 MultiSITE Edge 10

Бренды по названию

Популярные бренды