manualshive.com logo in svg

LG ARWN038GA2, Установка, эксплуатация и обслуживание, Страница: 87 / 92

Поделиться
Скачать
LG ARWN038GA2 Скачать руководство пользователя страница 87

*This form must be completed and submitted to LG a minimum of three (3) weeks prior to final scheduling of any startup.

Note: If any of the above items are not complete at time of start-up, back charges will be assessed for additional costs.

Contractor Name:  ______________________________________    ____________________________________________________

        

 

 

(Authorized 

Signature)

Address:  ____________________________________________

                ____________________________________________

                 

Phone:  _____________________________________________    Date:   _______________________________________________

PRE-COMMISSIONING CHECKLIST

Page 2

Prepare Pre-commissioning Package Documents

Include

Check

1.  A copy of the refrigerant piping system(s) shop drawing(s) generated by LATS Multi V pipe design software.

2.  A copy of the pipe fitter’s pipe changes and field notes.

3.  A verified copy of the “As-Built” LATS Multi V Project file (*.mtv) that includes all changes noted by the pipe fitter(s) in  

Number  2. The tree diagram notes should include changes to the line lengths used for each liquid line segment

4.  A copy of a completed and verified Installation Checklist for the water source unit, indoor units, ERVs, Air Cleaners, and Con-

trol Devices. Correct any procedures needing attention before initiating a request for commissioning..

5.  A copy of the air balance report showing proper airflow at all indoor units.

6.  A copy of the water circuit’s control sequence of operation.

7.  A water circuit flow balancing report.

8.  A completed Pre-commissioning Device Configuration Worksheet.

9.  A completed copy of the Pre-commissioning Checklist.

10. If available, a list of IP addresses obtained from the building owners IT department for each ACP, BacNet, LonWorks, AC Smart 

II, AC Smart Premium devices.

Initiate a Commissioning Request

Description

Check

Verify this checklist and requirements herein have been met. Complete this checklist in its entirety BEFORE initiating a request for 

Commissioning..

Send all Pre-commissioning Package Documents to your LG Applied Representative.

Содержание ARWN038GA2





























































































Отзывы:

Нет отзывов