manualshive.com logo in svg

LG ARWN038GA2, Установка, эксплуатация и обслуживание, Страница: 61 / 92

Поделиться
Скачать
LG ARWN038GA2 Скачать руководство пользователя страница 61

61

Electrical System Installation

Due to our policy of continuous product innovation, some specifications may change without notification.  

©LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. “LG” is a registered trademark of LG Corp.

Figure 64: Water Source to Indoor Unit Communications Cable Termination Detail. 

Communication Cables Between the Water Source Unit and the Indoor Units

Between Water Mini Unit and Indoor Units

IDU B

SODU B

INT B

SODU A

IDU A

INT A

TR / TQ Cassette Frames and 

All Other Indoor Unit Styles

TM / TN / TP Cassette 

Frames Only

1(L1) 2(L2)

3(A) 4(B)

1(L1) 2(L2) 3(L1) 4(L2)

6(B)

5(A)

DRY 1 DRY 2 GND

The terminal tagged “GND” on the water source unit main PCB is not an earth ground terminal. It is a neutral (-) terminal provided to connect 

the water source unit to central control devices.

Communications Cables

ELECTRICAL SYSTEM INSTALLATION

• Field Provided 18 Gauge Stranded Two-core 

Cable (Shielded)

• Insulation material as recommended by local 

code.

Communication Cables Between the Water Source Unit and the Central  

Control Device

• Field Provided 18 Gauge Stranded Two-core Cable (Shielded)
• Insulation material as recommended by local code.

Connect all central control devices such as AC Smart II, AC Smart Premium, ACP, BACnet and LonWorks gateways, and energy recovery 

ventilators all on the same cable. Order does not matter. Polarity does. Keep “A” terminals with “A” terminals, and “B” terminals with “B” 

terminals. Starting at the water source unit, terminate the cable on terminals Internet A and Internet B.  Route the cable as needed between 

each device. 

Note:

Connect the shield to ground ONLY at the water source unit. Tie shields together at each termination point.

Note:

Содержание ARWN038GA2





























































































Отзывы:

Нет отзывов