LG ARWN038GA2 Скачать руководство пользователя страница 22

Страница: 22 / 92

MUL

TI V W

ater Mini System Installation Manual

Due to our policy of continuous product innovation, some specifications may change without notification.

Device Connection Limitations

• The minimum number of connected and operating indoor units to a Multi V Water Mini system is one, taking into consideration of the mini-

mum combination ratio.

• The maximum number of indoor units on a Multi V Water Mini heat pump systems is:

One of the most critical elements of a Multi V Water Mini system is the refrigerant piping. The table below lists pipe length limits that must be

followed in the design of a Multi V Water Mini refrigerant pipe system:

Table 7: Multi V Water Mini Liquid Refrigerant Pipe Design Limitations.

Pipe Length

(ELF = Equivalent Length of pipe

in Feet)

Longest total equivalent piping length

≤475.7 feet

Longest distance from water source unit to indoor

unit

230 feet (Actual)

295.2 feet (Equivalent)

Distance between fittings and indoor units

≥20 inches

Distance between fittings and Y-branches

≥20 inches

Distance between two Y-branches

≥20 inches

Distance between Header and indoor units

≥20 inches

Minimum distance between indoor unit to any

Y-branch

3 feet from indoor unit to Y-branch

Maximum distance between first Y-branch to farthest

indoor unit

≤ 131 feet

Elevation (All Elevation

Limitations are Measured in

Actual Feet)

Water-source unit above or below indoor unit

≤ 98.4 feet

Between any two indoor units

≤ 49 feet

Table 8:

Equivalent Piping Length for Y-branches, Headers, and Typical Refrigeration Elbows.

Component

Size (Inches)

1/4

3/8

1/2

5/8

3/4

7/8

1-1/8

1-1/4

1-3/8

1-1/2

1-5/8

1-3/4

2-1/8

Elbow (ft.)

0.5

0.6

0.7

0.8

1.2

1.3

1.5

1.6

1.8

2.0

2.1

2.3

2.5

2.8

Y-branch (ft.)

1.6

Header (ft.)

3.3

Kit contains two Y-branches: one for liquid and one for vapor.

ARWN038GA2 = 6

ARWN048GA2 = 8

ARWN053GA2 = 9

REFRIGERANT PIPING DESIGN

System Engineering

Содержание ARWN038GA2





























































































Результаты поиска

Содержание ARWN038GA2

Отзывы:

LG ARWN038GA2, Установка, эксплуатация и обслуживание, Страница: 22 / 92

Результаты поиска

Содержание ARWN038GA2

Отзывы: