manualshive.com logo in svg

LG ARWN038GA2, Установка, эксплуатация и обслуживание, Страница: 15 / 92

Поделиться
Скачать
LG ARWN038GA2 Скачать руководство пользователя страница 15

15

Product Data

Due to our policy of continuous product innovation, some specifications may change without notification.  

©LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. “LG” is a registered trademark of LG Corp.

ACCESSORIES

Required Accessories

Model No.

Y-branches  

(for indoor unit connection)

ARBLN01621

ARBLN03321

Headers  

(for indoor unit connection)

Four (4) branch

Seven (7) branch

Ten (10) branch

ARBL054

ARBL057

ARBL1010

ARBL104

ARBL107

ARBL2010

Vapor pipe

Liquid pipe

Unit: Inch

Models

ARBLN01621

ARBLN03321

16-1/4

15-3//8

I.D. 3/4

I.D. 3/4

I.D. 3/4

I.D. 3/4

O.D. 5/8

I.D. 1/2

I.D. 5/8

I.D. 5/8

I.D. 5/8 

I.D. 1/2

I.D. 1/2

I.D. 1/2

I.D. 1/2

I.D. 1/2

I.D. 1/2

I.D. 1/2

I.D. 1/2

11-1/2

11-1/16 

11-1/2

11-1/16 

2-15/16

2-15/16

2-15/16

2-3/4

2-3/4

2-3/4

I.D. 5/8

I.D. 5/8

I.D. 1

I.D. 1

O.D. 1

3-3/16

4-3/8

13-1/16

12-5/8

3-5/16

1

2

3

3

O.D. 3/4

O.D. 3/4

1 2

I.D. 7/8

I.D. 7/8

I.D. 7/8

I.D. 1/4

I.D. 1/4

I.D. 1/4

I.D. 1/4

I.D. 1/4

1

1

1

1

I.D. 1-1/8

I.D. 3/8

I.D. 3/8

I.D. 3/8

I.D. 3/8

I.D. 3/8

I.D. 3/8

O.D. 3/8

Table 3:  Y-branch Table.

Table 4: Required Accessories.

Y-branches (for indoor unit connection)

Содержание ARWN038GA2





























































































Отзывы:

Нет отзывов