LG ARWN038GA2 Скачать руководство пользователя страница 24

Страница: 24 / 92

MUL

TI V W

ater Mini System Installation Manual

Due to our policy of continuous product innovation, some specifications may change without notification.

REFRIGERANT PIPING DESIGN

System Engineering

LG Y-branch kits consist of:

• Y-branches (liquid line, vapor lines).

• Reducer fittings as applicable.

• Molded clam-shell type insulation covers.

LG Header kits consist of:

• Two Headers (one liquid line, one vapor line).

• Reducer fittings as applicable.

• Molded clam-shell type insulation covers.

LG Engineered Y-branch Kits and Header Kits

Y-Branch Kits

LG supplied Y-branches must be used at each transition. Field-supplied “T” fit-

tings or “Y” branches are not acceptable. Each LG supplied Y-branch kit comes

with two (2) Y-branches for indoor units, step-down pipe reducers, and insulation

covers.
Y-branches may be installed in horizontal or vertical configurations. When in-

stalled vertically, position the Y-branch so the straight-through leg is ±3° of plumb.

When installed horizontally, position the Y-branch so the take-off leg is level and

shares the same horizontal plane as the straight-through leg ±5° rotation.

There is no limitation on the number of Y-branches that can be installed, but there

is a limitation on the number of indoor units connected to a single water source

unit.
Y-branches should always be installed with the single port facing the water-source

unit, the two-port end facing indoor units (Do not install Y-branches backwards as

shown in Figure 15.) Refrigerant flow cannot make U-turns through Y-branches.

The first Y-branch kit must be located at least three (3) feet from the water source

Figure 12: Y-branch Connections.

Figure 13:

Y-branch Installation Alignment Specification.

Vertical up configuration.

Vertical down configuration.

Figure 14: Horizontal Configuration End View.

±5°

Horizontal Plane

±5°

Branch Leg

Straight-through Leg

Y-branch Inlet

To indoor unit

To outdoor unit

To next branch

To indoor unit

Figure 15:

Diagram of an Incorrect Y-branch

Installation.

LG Y-branch and Header kits are highly engineered devices designed to evenly divide the flow of refrigerant, and are used to join

one pipe

segment to two or more segments.

No Substitutions

Only LG supplied Y-branch and Header fittings (as referenced below; sold separately) can be used to join one pipe segment to two or more

segments. Third-party or field-fabricated Tee’s, Y-fittings, Headers, or other branch fittings are not qualified for use with LG Multi V Water Mini

systems. The only field-provided fittings allowed in a Multi V Water Mini piping system are 45° and 90° elbows.

Y-branches

Headers

4 branch

7 branch

10 branch

ARBLN01621

ARBL054

ARBL057

ARBL1010

ARBLN03321

ARBL104

ARBL107

ARBL2010

Table 12: Y-Branches and Headers.

• If the diameter of the branch pipe segments differ from that of the designated refrigerant piping, trim the to the desired section using a pipe

cutter, and then use an adapter to connect.

•

Always follow manufacturer’s guidelines on refrigerant piping restrictions such as maximum length, elevation difference, and diameters. Fail

ure to do so can result in reduced heating / cooling performance or equipment malfunction.

unit. Provide a minimum of 20

inches between a Y-branch and

any other fittings or indoor unit

piped in series. It is recom-

mended that when a Y-branch is

located in a pipe chase or other

concealed space, access doors

should be provided for inspec-

tion access. The equivalent pipe

length of each Y-branch (1.6′)

must be added to each pipe

segment entered into LATS pip-

ing design software.

Содержание ARWN038GA2





























































































Результаты поиска

Содержание ARWN038GA2

Отзывы:

LG ARWN038GA2, Установка, эксплуатация и обслуживание, Страница: 24 / 92

Результаты поиска

Содержание ARWN038GA2

Отзывы: