level 1 H-1200 115V Скачать руководство пользователя

Страница: 32 / 82

Operator’s Manual

Interlocks

The Fluid Warmer has five Interlocks that detect for proper installation
of a Disposable Set’s components. Refer to the figure on the facing page
to identify the positions of interlocks.

Note:

Block

is not an Interlock. It cannot detect if a Disposable Set

is not correctly installed. It is identified here because it is an essential
step for proper installation of the Disposable Set components.

Three Interlocks are located on the Fluid Warmer and check for proper
installation of:

Heat Exchanger, top end

Gas Vent/Filter Assembly

Heat Exchanger (guide)

Two Interlocks are located in the Air Detector/Clamp

and check for

the proper installation of:

Patient I.V. Line in the Clamp Slot
Door for the Clamp Slot

Interlocks

2, 4,

and

prevent the Fluid Warmer’s pump from

circulating reservoir solution if the Disposable Set’s Heat Exchanger and
Gas Vent/Filter Assembly are not installed properly.

If Check Disposable Alarm is Activated on the Fluid Warmer

Check Heat Exchanger for proper installation in Block

, and

Interlocks

and

Press Heat Exchanger down firmly in Block

to secure in O-Ring.

Press Interlock

tab down firmly to engage the Interlock switch.

Press Heat Exchanger firmly into Interlock

Check Gas Vent/Filter Assembly installation in Interlock

If Check Tubing Alarm is Activated on the Air Detector/Clamp

Open the door and check the Patient Line for proper installation in
the Clamp Slot at interlock

Close the door and check that the tab on the top edge of the door is
fully inserted into the Air Detector/Clamp at interlock

before

pushing the door down to close it.

S E C T I O N 7 • C o n t r o l s a n d D i s p l a y s

Содержание H-1200 115V



















































































Результаты поиска

Содержание H-1200 115V

Отзывы:

Похожие инструкции для H-1200 115V

Бренды по названию

Популярные бренды

level 1 H-1200 115V, Руководство оператора

Результаты поиска

Содержание H-1200 115V

Отзывы:

Похожие инструкции для H-1200 115V

Бренды по названию

Популярные бренды