manualshive.com logo in svg

level 1 H-1200 115V, Руководство оператора

Поделиться
Скачать
level 1 H-1200 115V Скачать руководство пользователя страница 30

|

Operator’s Manual

Air Detector/Clamp Control Panel and Alarms

The Air Detector/Clamp Control Panel has three LED indicators that
display the operational state of the Air Detector/Clamp. Refer to figure
on right.

1

Automatic Operation LED

The green Automatic Operation LED illuminates when the 
following conditions are present: The Fluid Warmer power is
ON, a Disposable Set is properly installed in the Fluid Warmer
and primed, the patient line from the Gas Vent/Filter Assembly
is correctly placed in the #3 Clamp Slot, and the Clamp Slot
door is closed.

2

Check Tubing LED

The yellow Check Tubing LED illuminates and an audible 
attention signal beeps when the patient line tubing from the Gas
Vent/Filter Assembly is not correctly placed in the #3 Clamp
slot, and when the Clamp Slot door is not closed correctly.

3

Clamped LED

The red Clamped LED illuminates and an audible warning signal
beeps when air is detected in the Gas Vent/Filter Assembly. The
patient line is automatically clamped. 

S E C T I O N   7   •   C o n t r o l s   a n d   D i s p l a y s

24

Содержание H-1200 115V



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды