Lenze SimpleServo 94 страница 39 Скачать руководство пользователя | Manualshive

Страница: 39 / 66

background image

IMS94S-mv1

l

37

6.6.6 Enable input de-bounce time

Sets de-bounce for the enable input to anticipate switch or relay contacts bouncing if
they are used to compute input.

6.7 Velocity Limits Group

These parameters are active in Velocity Mode Only.

• Zero speed

(velocity mode only)

• Speed window (velocity mode only)
• At speed

(velocity mode only)

ZERO SPEED

speciﬁes the lower threshold for motor zero speed in RPM. When

motor shaft speed is below speciﬁed value the zero speed condition is set to true in
the internal controller logic. The zero speed condition can also trigger a programmable
digital output, if selected.

SPEED WINDOW

speciﬁes the speed window width.

AT SPEED

speciﬁes the speed window center.

These last two parameters specify speed limits. If motor the shaft speed is within
these limits then the condition AT SPEED is set to TRUE in the internal controller
logic. The AT SPEED condition can also trigger a programmable digital output, if
selected.

For example if “AT SPEED” is set for 1000 RPM, and the “SPEED WINDOW” is set
for 100, then “AT SPEED” will be true when the motor velocity is between 950 -1050
RPM.

6.8 Position limits

• Position error

• Max error time

• Second encoder position error

• Second encoder max error time

POSITION ERROR

speciﬁes maximum allowable error (in quadrature encoder

counts) before Position Error Excess fault generated.

MAX ERROR TIME

speciﬁes maximum allowable time (in mS) during which

position error can exceed value set for POSITION ERROR
parameter before Position Error Excess fault generated.

6.9 Compensation group

·

Velocity P-gain (Proportional)

Proportional gain adjusts the system’s overall response to velocity error. Velocity
error is the difference between the commanded velocity of a motor shaft and the
actual shaft velocity. By adjusting the proportional gain, the bandwidth of the drive is
more closely matched to the bandwidth of the control signal, ensuring more precise
response of the servo loop to the input signal.

«
...
37
38
39
40
41
...
»

Содержание SimpleServo 94



































































Отзывы:

Нет отзывов

Похожие инструкции для SimpleServo 94

Бренд: ECG Страницы: 15

Бренд: Vacon Страницы: 60

Бренд: Vacon Страницы: 192

Бренд: Parker Страницы: 103

Compax3H C3H1xxV4 Series

Бренд: Parker Страницы: 44

Бренд: Astor Страницы: 276

Бренд: RIB Страницы: 44

Бренд: YASKAWA Страницы: 306

Бренд: HAUTAU Страницы: 8

Бренд: LinMot Страницы: 91

Бренд: WEG Страницы: 212

Бренд: NEC Страницы: 2

Xtreme Advantage SCX

Бренд: IMCO Страницы: 25

ZRK-EMLV2-30W-XXDC

Бренд: Zurik Страницы: 9

Бренд: SureStep Страницы: 16

Бренд: Moeller Страницы: 8

Бренд: Moeller Страницы: 11

Бренд: Montech Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды