Lenze L-force 930 Скачать руководство пользователя страница 157

Страница: 157 / 199

Appendix

Communication interfaces

Control via CAN bus



157

SW-HB 13.0002-EN EN 3.0

10.2

Communication interfaces

10.2.1

Control via CAN bus

Functions available

The 931E servo positioning controller uses the CANopen protocol according to

DS301 / DSP402.
The following operating modes specified in CANopen are supported:

Torque control (profile torque mode)

Speed control (profile velocity mode)

Homing (homing mode)

Positioning (profile position mode)

Synchronous position selection (interpolated position mode)

The following access types are supported for data exchange:

Access type

Description

SDO

Service Data Object

Used for the standard parameterisation of the controller.

(Approx. 150 SDOs are supported.)

PDO

Process Data Object

Fast exchange of process data (e.g. actual speed) possible. (2

PDOs are supported.)

SYNC

Synchronisation Message

Synchronisation of several CAN nodes.

EMCY

Emergency Message

Transfer of error messages.

NMT

Network Management

Network service: E.g. all CAN nodes can be influenced at the same

time.

HEARTBEAT Error Control Protocol

The bus devices are monitored by means of regular messages.

efesotomasyon.com - Lenze

Содержание L-force 930








































































































































































































Результаты поиска

Содержание L-force 930

Отзывы:

Lenze L-force 930, Руководство пользователя программного обеспечения, Страница: 157 / 199

Результаты поиска

Содержание L-force 930

Отзывы: