Lenovo 7X69 Скачать руководство пользователя страница 102

Страница: 102 / 172

To remove the chassis air baffle, complete the following steps:

Watch the procedure

A video of this procedure is available at YouTube:

https://www.youtube.com/watch?v=pIb0bIyfkDY&=

PLYV5R7hVcs-Ak9fT8QAx8fLbEivizjRtp

Figure 56. Chassis air baffle removal

Table 76. Chassis air baffle release latch

Release latches

Step 1. Press the chassis air baffle release latches; then, lift the chassis air baffle out from the server.

Note:

For proper cooling and airflow, reinstall the chassis air baffle before you install the server

into the rack. Operating the server with the chassis air baffle removed might damage server
components.

If you are instructed to return the component or optional device, follow all packaging instructions, and use
any packaging materials for shipping that are supplied to you.

Remove the system board air baffle and the power interposer

Use this procedure to remove the system board air baffle and the power interposer.

Note:

If the server comes with a processor and memory expansion tray, it does not come with this

component.

Before removing the system board air baffle, complete the following steps:

ThinkSystem SR860 Setup Guide

Содержание 7X69













































































































































































Результаты поиска

Содержание 7X69

Отзывы:

Похожие инструкции для 7X69

Бренды по названию

Популярные бренды

Lenovo 7X69, Руководство по установке

Результаты поиска

Содержание 7X69

Отзывы:

Похожие инструкции для 7X69

Бренды по названию

Популярные бренды