Lenovo 7X69 Скачать руководство пользователя страница 117

Страница: 117 / 172

Figure 68. Drive installation

Step 5. Rotate the drive-tray handle back to the locked position.

After installing the 2.5-inch hot-swap drive, check the drive status LED to verify if the drive is operating
correctly:

• If the yellow LED is lit continuously, it is malfunctioning and must be replaced.
• If the green LED is flashing, the drive is functioning.

Note:

If the server is configured for RAID operation through a ThinkSystem RAID adapter, you might have to

reconfigure your disk arrays after you install drives. See the ThinkSystem RAID adapter documentation for
additional information about RAID operation and complete instructions for using ThinkSystem RAID
adapters.

Install the fan cage assembly

Use this procedure to install the fan cage assembly.

Before installing the fan cage assembly:

1. Read the safety information and installation guidelines (see

“Safety” on page iii

and

“Installation

Guidelines” on page 56

2. Touch the static-protective package that contains the component to any unpainted metal surface on the

server; then, remove it from the package and place it on a static-protective surface.

To install the fan cage assembly, complete the following steps:

Watch the procedure

A video of this procedure is available at YouTube:

https://www.youtube.com/watch?v=pIb0bIyfkDY&=

PLYV5R7hVcs-Ak9fT8QAx8fLbEivizjRtp

Chapter 3

Server hardware setup

109

Содержание 7X69













































































































































































Результаты поиска

Содержание 7X69

Отзывы:

Похожие инструкции для 7X69

Бренды по названию

Популярные бренды

Lenovo 7X69, Руководство по установке

Результаты поиска

Содержание 7X69

Отзывы:

Похожие инструкции для 7X69

Бренды по названию

Популярные бренды