Lennox Core Unit Controller Скачать руководство пользователя страница 4

Страница: 4 / 92

J386

J387

J388

J389

J390

J391 J392

J393

J395

J394

MODBUS

J413

LONTalk

Module

24VAC

Gnd

S-BUS SmartWire

™

System J304

Humidistat

Digital

Inputs

Smoke

24VAC

Gnd

24VAC

Thermostat

Service Relays

R + C

Spare

Analog

Inputs

Room

and RH

Sensors

Sensor

IAQ

J358

Duct Sensor

J378

4-Character Seven

Segment LED

J379

J380

J381

J382

J383

J385

J384

J298

J297

J299

Sensor

IAQ

A11

HUM TMP

Sensor

Inputs

A12 C R

White Push

Button

Black Push

Button

Service Relays

S-BUS

Factory Test

P2 Expansion

Card Connection

(C4)

CORE Unit Controller (A55)

Wireless Control (W4)

Figure 1. Lennox CORE Unit Controller Interfaces and LEDs Locations

• LED Indicators

NOTE:

CORE™ Control System features vary with the

type of rooftop unit in which the control is installed.

1.6. Lennox CORE Unit Controller -

Connections, Inputs / Outputs,

Jumpers, and LEDs Locations

THERMOSTAT COMMON ISOLATION - TSTAT_COM

Jumper

Thermostat (TSTAT) sensor commons are located on

connector P298 and may be isolated if they are powered

remotely. Remove jumper.

This jumper is located to the left of P297 connector. This

jumper would be removed only in unique situations where

the device supplying the thermostat signals to the CORE

Unit Controller has its own power source and does not share

a common reference voltage with the CORE unit controller.

Otherwise the jumper would remain installed across both

pins, as shipped from the factory.

A. HUMIDISTAT COMMON ISOLATION -

HMD_COM

Jumper

The humidity (HUM) sensor commons are located on

connector P298 and may be isolated if they are powered

remotely. Remove jumper. This jumper is located to the right

of P299 connector. This jumper would be removed only in

unique situations where the device supplying the thermostat/

humidistat signals to the CORE Unit Controller has its own

power source and does not share a common reference

voltage with the CORE Unit Controller. Otherwise the jumper

would remain installed across both pins, as shipped from the

factory.

b. W4 CONTROL - USb FLASH DRIVE INTERFACE

USAGE

The W4 Control uses a USB type A interface. This USB port is

used for verifying service, downloading reports, transferring

unit profiles and performing firmware updates.

On-site data collection requires use of either a USB flash

drive or download and shared from the CORE Service App.

Data written to the drive includes date, time, serial number,

catalog number, basic data, error code buffer, and unit

configuration.

C. S-bUS (SMARTWIRE

™

) (J304)

This is the L-connection interface. This is a R485 network

connection with other devices (NCP, comfort sensors, other

RTU, etc.).

D. MODbUS CONNECTION (J413)

This is a TIA-485 serial line over MODBUS (messaging

structure) communication. This connection is used for

multiple components.

E. CORE UNIT CONTROLLER LED INDICATORS

NOTE:

See “g. Local Interface - four character seven

segment LED - Status Codes” on page 5 for

further information.

Содержание Core Unit Controller





























































































Результаты поиска

Содержание Core Unit Controller

Отзывы:

Похожие инструкции для Core Unit Controller

Бренды по названию

Популярные бренды

Lennox Core Unit Controller, Руководство по установке

Результаты поиска

Содержание Core Unit Controller

Отзывы:

Похожие инструкции для Core Unit Controller

Бренды по названию

Популярные бренды