Lennox Core Unit Controller Скачать руководство пользователя страница 6

Страница: 6 / 92

1.7. W4 Wireless Controller - Connections, buttons and LEDs

Wireless Board (W4)

Service App QR Code

* Allow users to quickly find the service app

2-Port IP Switch

BACnet IP

* Automatic firmware updates

* Allows daisy-chain connection

USB port

* Firmware Updates

* System Logs and Reports

* Configuration save/copy

Wireless Gateway Connector

* Connects to unit gateway (coax)

* Allows app and sensor connections

BACnet MS/TP

* Standard on all CORE Unit Controllers

* New objects supported

Pair Button and LED

* Pressing button allows

pairing to App.

* LED indicates pairing status - solid

blue indicates either BLE is booting up

or mobile device is already connected.

Green indicates ready for connection.

Blinking blue indicates in pairing mode.

Reset Button and Heart

Beat LED

* Reset Button for the W4 control

* Blinking LED indicates W4 power

Cloud / IP Button and LED

* Button not used at this time

* LED indicates BACnet and cloud

connectivity. Red LED indicates not

connected and green indicates connected.

Figure 3. W4 Controller Interfaces

1.8. Cloud Firmware Updates

•  Internet connection is required
•  On-demand or automatic
•  CORE Unit Controller connects to cloud via IP (Ethernet)
•  Can check on demand or nightly

Configurable via app

> Default: On demand

• Free updates
• Updates are also available via USB

2. Network Types

The following are the types of communication network types

supported.

Table 3. Network Types

Screen Label

Network Type

LON

LonTalk

BACNET

BACnet MS/TP and IP

LCONN

L-Connection

RTU

Rooftop Unit stand-alone mode status

indicator

3. Unit Operation

This section describes the display and control buttons, how

to configure the unit, and how to read stored configuration

data, status, and alarms.

The CORE Unit Controller is an input and output junction

point. If in the thermostat mode, thermostat inputs at P297

result in an output to unit components. If the heartbeat LED

is not flashing, see ”Table 1. LED Operation Indicators” on

page 5 for heartbeat operation. If the display shows

an alarm. If the thermostat input indicating lights are not

responding appropriately, check the thermostat or a DDC

control acting as thermostat inputs into P297.

Basic cooling and heating functions may be energized to test

major unit components by using the CORE Unit Controller

testing function or by using jumper wires on the Field Wiring

Termination plug P297.

Содержание Core Unit Controller





























































































Результаты поиска

Содержание Core Unit Controller

Отзывы:

Бренды по названию

Популярные бренды

Lennox Core Unit Controller, Руководство по установке

Результаты поиска

Содержание Core Unit Controller

Отзывы:

Бренды по названию

Популярные бренды