Lennox Core Unit Controller Скачать руководство пользователя страница 30

Страница: 30 / 92

10.3. Enabling Economizer and Settings

The economizer, when configured, controls:

• Damper position, which determines how much outdoor

air is used to meet free cooling or indoor air quality

requirements, and

• Optional power exhaust fans.

On a cooling demand, outdoor air is used for free cooling

instead of first-stage compressor(s) when outdoor air is

suitable.

To enable the economizer if installed:

Go to SETUP > INSTALL

When reaching Configuration ID 1, position 2 will need to

be set to the applicable type of economizer. Valid types are:

•

= Motorized Outdoor Air Damper Only

•

= Economizer - Temperature (Note: Used for both set

point and offset temperature control.)

•

= Economizer - Global

•

= Economizer - Single Enthalpy

•

= Economizer - Dual Enthalpy

10.3.1. Damper Feedback Calibration

Use the following procedure to perform a damper feedback

calibration.

Go to SETUP > TEST & BALANCE > DAMPER > IS DAMPER

CLOSED?

This drives the damper to the fully closed position. Visually

inspect that the damper has stopped moving in the closed

position, and answer

YES

to calibrate damper closed

position feedback value.

Then the next screen will ask

IS DMPR FULL OPEN

This will drive the damper to fully open position. Visually

inspect that the damper has stopped moving in the full open

position, and answer

YES

to calibrate damper full open

position feedback value.

10.3.2. Damper Operation During Free

Cooling

These are operating profile options for the economizer

damper (Parameter 164 - ECONOMIZER PROFILE) during

free cooling when any compressor is on and can be selected

as follows:

Damper opens to its max open position (Parameter 131 -

FREE CL MAX DAMPER) when any compressors start.

NOTE:

When using Option 1 and after the compressor is

stopped, the M3 shall resume damper modulation.

10.4. Free Cooling Compressor Lockout

Mode and Low Ambient Set Point

Go to SETTINGS > RTU OPTION > EDIT PARAMETER > COOLING =

285 (FRCL COMP LCKOUT MD).

Default value is 2. Range is 0 to 2.

•

= Disable Compressor Lockout

•

= Lockout Compressor if outdoor air is suitable

regardless of outdoor air temperature.

•

= Lockout Compressor if outdoor air temperature is

below Parameter 108 setting and Outdoor Air is Suitable

(Default).

Go to SETTINGS > RTU OPTION > EDIT PARAMETER = 108

(FREE LO AMB LCKT SP).

Default value is 55.0°F. Range is 45.0 to 80.0°F.

10.4.1. Outdoor Air Suitable for Free

Cooling

The CORE Unit Controller displays the outdoor air suitability

information on the status screen.

The appropriate sensors are provided when the economizer

is factory-configured. When the economizer is field-installed

and configured, the single or dual enthalpy modes require

additional field-provided sensor(s).

10.4.2. Enthalpy Set Point

This setting pertains to the single enthalpy free cooling mode

only. The CORE Unit Controller will enable free cooling

when outdoor air enthalpy (A7) is less than the enthalpy set

point (Parameter 162 - ECON FREECL ENTH SP). Figure

6 shows the approximate enthalpy sensor output at various

temperatures and percentage of relative humidity.

40°F

50°F

60°F

70°F

80°F 90°F 100°F

30
20
10

100

Figure 31. Enthalpy Sensor Output Current

Honeywell C7400

10.4.3. Free Cooling Damper Maximum

Position

Damper Maximum position for free cooling is by default set

to 100%. To modify this settings, use the following path:

SETTINGS > RTU OPTION > EDIT PARAMETER > AIR FLOW >

131 (FREE CL MAX DAMPER)

10.4.4. Minimum Damper Position

Use the following menu path to modified the minimum

damper positions for both high and low operations.

SETUP > TEST & BALANCE > DAMPER > CLOSING DAMPER >

OPEN DAMPER > TURN BLOWER ON > MIN DAMPER POSITION

BLOWER ON HIGH = .%

SETUP > TEST & BALANCE > DAMPER > CLOSING DAMPER >

Содержание Core Unit Controller





























































































Результаты поиска

Содержание Core Unit Controller

Отзывы:

Бренды по названию

Популярные бренды

Lennox Core Unit Controller, Руководство по установке

Результаты поиска

Содержание Core Unit Controller

Отзывы:

Бренды по названию

Популярные бренды