Lennox Core Unit Controller Скачать руководство пользователя страница 27

Страница: 27 / 92

RTU

OPTIONS

BLOWER ON

POWER

EXHAUST

EXTERNAL ENABLE

VAV

SUMMARY

EDIT

PARAMETER

OCCUPIED

ALWAYS

SET POWER EXHAUST

ECONOMIZER TRAVEL

SETPOINTS

SET POWER EXHAUST

BUILDING PRESSURE

SET DAMPER FRESH AIR

TEMPERING SETPOINTS

AIRFLOW

MISCELLANEOUS

HEATING

COOLING

ECONOMIZER

CONTROL OPTIONS

PERFORM A MANUAL SEARCH FOR A SPECIFIC PARAMETER (NOTE: NOT ALL

PARAMETERS CAN BE ACCESS THROUGH THE EDIT PARMETER TOOL)

Figure 29. Settings - Power Exhaust and Edit Parameter

9.4.2. Install

The mobile application provides a menu to run “New Unit Setup”.

•  New Unit setup if chosen shall direct the user towards the install menu.
•  The mobile application shall provide a menu to run “Install New M4” (CORE Unit Controller).
•  Install new CORE Unit Controller

will first confirm with the user if it is okay to “Clear all Configuration”.

•

If the user confirms that it is okay to “Clear All Configuration”, the app shall ask the user if they are sure.

•

If the user confirms, the menu directs the user towards the Setup >RTU Menu > INSTALL.

• If the user cancels at any point, they shall be taken back to the Setup >RTU Menu > INSTALL.

INSTALL

NEW UNIT SETUP

SELECT

INSTALL

OPTION

INSTALL NEW M4

SEE FIGURE 9 FOR ADDITIONAL

INSTALL SETTING.

DATE AND

TIME

RTU NAME

MODEL NUMBER

SERIAL NUMBER

CATALOG NUMBER

CONFIGURATION ID 1

CONFIGURATION ID 2

YES OR CANCEL

CONFIRM AGAIN

Figure 30. Settings - Install

Содержание Core Unit Controller





























































































Результаты поиска

Содержание Core Unit Controller

Отзывы:

Бренды по названию

Популярные бренды

Lennox Core Unit Controller, Руководство по установке

Результаты поиска

Содержание Core Unit Controller

Отзывы:

Бренды по названию

Популярные бренды