16
BUTTON CONFIGURATION
Button Configuration enables communication between the
load, its assigned switch and the LMCT-100. Use the Button
Configuration screen to assign the button to a specific button
function type, and to change parameter values such as modes
and fade times, based on the function type.
Press
Select
Point at Switch,
Press Select,
All Blue LEDs on
Switch Blink
Continue Pointing
at Switch,
Press Button,
The Button’s LED Blinks
P o i n t a t s w i t c h a n d
P r e s s ‘ S e l e c t ’
C o n t i n u e p o i n t i n g t o
t h e s w i t c h , t h e n
p r e s s t h e b u t t o n y o u
w i s h t o c o n fi g u r e
S e n s o r C o n fi g u r a t i o n
L o a d C o n fi g ( P n L )
D a y l i g h t i n g C o n fi g
B u t t o n C o n fi g u r a t i o n
D i m m i n g C o n fi g u r a t i o n
M o r e
=
B AT
Based on whether the button pressed is a Scene Button, Load
Button Rocker Button, or Group Button, one of the following
screens is presented.
Scene Button
Rocker Button
Rocker Button Config
<0058721386>
Fade On:
<Use Load’s>
Fade Off:
<Use Load’s>
Ramp Rate:
<17%/sec>
LOADS
SEND NEXT BUTTON
Load Button
Button Config
<0058721386>
Type:
<Load>
Mode:
<Toggle>
Fade On:
<Use Load’s>
Fade Off:
<Use Load’s>
LOADS
SEND NEXT BUTTON
Scene Button Config
<0058721386>
Type:
<Scene 1>
Mode:
<Recall Scene>
Lock Button
<No>
Fade On:
<Use Load’s>
Fade Off:
<Use Load’s>
SEND NEXT BUTTON
Group Button
Button Config
<0058721386>
Type:
<Group>
Mode:
<ToggleNT>
Group ID:
<??>
SEND NEXT BUTTON
Load Button Parameters
Load Button Config
<0058721386>
Type:
<Load>
Mode:
<Toggle>
Fade On:
<Use Load’s>
Fade Off:
<Use Load’s>
ASSIGN LOADS
SEND NEXT BUTTON
Type
You may change the button type by scrolling through the values for
Type. Available values: Load, Scene 1 through Scene 16, or Group.
If you change between Load, Scene, or Group and press
, the
screen changes to show parameters particular to that button type.
NOTE:
The Rocker value will only appear for an actual rocker
switch.
Mode
Mode options for Load buttons are Toggle, On-Only, Off-Only,
and ToggleNT.
In On Only or Off Only mode, each button press only causes the
associated action.
In Toggle mode, if there are multiple loads bound to a button
and any load is ON, the LED will be lit. Pressing the button turns
OFF all loads and the LED on the button turns OFF. Pressing
the button again turns ON all loads bound to the button.
Any bound load ON
= LED ON
Bound loads OFF
= LED OFF
Bound loads ON
= LED ON
ToggleNT mode is intended for use when the button is assigned
to a Group. For details on this mode, see the section on
Fade On, Fade Off
Fade On and Fade Off determines the time that it takes for loads
bound to this button to reach the target level.
The fade time defaults are Use Load’s. By default, all loads carry
a two second ON and OFF fade time. Each button can be set for
different fade times independently for the same loads, allowing
fast or slow load fade, depending on the button pressed.
Fade time value options are from None (immediate) to 18
hours in duration. As you scroll through the values, the units of
measure change from seconds to minutes to hours.
Loads
Select this option to open the
Assign Loads
screen. This will
allow you select one or more loads to assign to the button .
See
Send
Select
SEND
point the LMCT-100-2 at the switch and press
Select again. You return to the Button Config screen and can
either configure another button or exit Button Configuration.
Next
Select
NEXT
to repeat the configuration process for the next
button in the switch.
Important:
If you make any changes to a button’s settings,
always choose
SEND
before going to the next button. New
settings are not saved until sent to the button.
Scene Button Parameters
Scene Button Config
<0058721386>
Type:
<Scene 1>
Mode:
<Recall Scene>
Lock Button
<No>
Fade On:
<Use Load’s>
Fade Off:
<Use Load’s>
SEND NEXT BUTTON
Type
You may change the button type by scrolling through the values
for Type. Available values: Load, Scene 1 through Scene 16, or
Group. If you change between Load, Scene, or Group and press
, the screen changes to show parameters particular to that
button type.
NOTE:
The Rocker value will only appear for an actual rocker
switch.
Mode
Mode options for Scene buttons are:
•
Recall Scene
(default) – Each time the button is pressed
turns ON the scene.
•
Scene Off
– Each time the button is pressed turns OFF the
scene. Note: when Scene Off mode is set, the blue LED on
the button is never lit.
•
Recall/OFF
– This is similar to a toggle function. Pressing
the button once when the scene is not active recalls the
scene; a subsequent button press while the scene is active
turns OFF all members of the scene.