Landoll Brillion SS16, Руководство оператора

Страница: 76 / 100

3-18 F-1021-0422
TABLE OF CONTENTS
General Operation
1. The minimum horsepower requirements are typically
6-8 horsepower per foot. This will vary widely due to
speed, depth, moisture, and types of soils. Local
dealers can help in making recommendations for your
areas. For 3-PT Hitch models size tractor by 3-PT
Hitch Capacity.
2. Operating speed is typically 4.5-6 mph. Excessive
speed can result in undesirable germination, seeder
bouncing, or other unpredictable results. Reduce
speed in rocky conditions to prevent wheel breakage.
Transporting the Seeder
1. Check and follow all federal, state, and local
requirements before transporting the Seeder.
2. The Seeder should be transported only by tractor
required for field operation. The implement weight
should not exceed more than 1.5 times the tractor
weight. Maximum transport speed for the Seeder is
20 mph for the implement.
CAUTION
3. When towing equipment in combination, the
maximum equipment ground speed shall be limited to
the lowest specified ground speed of any of the towed
implements.
4. Maximum transport speed shall be the lesser of travel
speed specified in the operator's manual, speed
identification symbol, information sign of towed
equipment, or limit of road conditions.
5. Slow down when driving on rough roads. Reduce
speed when turning, or on curves and slopes to avoid
tipping. Equipment altered other than the place of
manufacture may reduce the maximum transport
speed. Additional weight, added tanks, harrowing
attachments, etc. may reduce implement load
carrying capabilities.
6. A Safety Chain is provided with the implement to
ensure safe transport.
• The Safety Chain should have a tensile strength
equal to or greater than the gross weight of the
implement. The chain is attached to the lower
Hitch Clevis hole with two Flat Washers between
the Clamp Plates to assure a tight connection.
Always use a 1" diameter Grade 8 bolt for this
connection.
• Attach the Safety Chain to the tractor drawbar.
See Figures 1-2 and 1-3. Provide only enough
slack in the chain for turning. Do not use an
intermediate chain support as the attaching point
for the chain on the tractor. Do not pull the
implement by the Safety Chain.
• When unhitching from the tractor attach the hook
end of the chain to a free link close to the hitch
clevis for storage. This will keep the hook off the
ground, reducing corrosion, and keep the hook
functioning properly.
• Regularly inspect the safety chain for worn,
stretched, or broken links and ends. Replace the
safety chain if it is damaged or deformed in any
way.
7. Before transporting:
• Know the height and width of the implement being
towed. Markers, tanks, attachments, etc. can
increase the height and width of the implement.
DANGER
DANGER
• Check to see that the tractor hitch capacity is
rated to carry the weight of the Seeder Hitch.
Refer to Tractor Operator’s Manual.
• Use provided pins that properly fits the Lift Arms
or Quick Hitch and Implement Hitch.
• Clean all Hydraulic Couplings and attach to
tractor remotes.
• Connect Basic Clutch Switch Box or Brillion Elite
Mini Monitor System to tractor.
• Connect the Safety Warning Lights 7-Pin Plug
into tractor 7-Pin outlet, routing cord by avoiding
pinch points.
• Fully raise the Seeder Hydraulic Lift and 3-PT Hitch.
• Make sure all Transport Locks and Hair Pin
Cotters and Clevis Pins are installed. See
“Transport Lock Engaged” on page 3-5.
WARNING
Excessive speed may result in loss of control of
the tractor and implement, reduced braking
ability, or failure of the implement tire or structure.
Do not exceed the implement maximum specified
ground speed regardless of the capability of the
maximum tractor speed. Stay away from power lines when transporting,
extending implement. Electrocution can occur
without direct contact.
Failure to use transport lock pins during
transport may result in permanent equipment
damage, serious injury, or death.