Landoll Brillion SS16, Руководство оператора

Страница: 37 / 100

F-1021-0422 2-19
TABLE OF CONTENTS
Brillion Elite Mini Monitor -
Field Installation - Optional
Assembly instruction for models with an installed Clutch.
IMPORTANT
The Brillion Elite Mini Monitor System by Loup
utilizes a MUX communication line. Sensors must be
learned into the Monitor. Location of each pre-learned
Smart Shaft Sensor or Bin Level Sensor is important
for proper Monitor display. Each Sensor utilizes
3 wires (+, -, MuxBus) to connect to the system. The
Harnesses do not require a specific Sensor
connection points. Each Sensor is identified in the
Monitor by its own signal.
WARNING
IMPORTANT
All Harnesses must be firmly attached to Machine
Frame members so they do not sag or become torn
loose by field debris.
Refer to Brillion Elite Mini Monitor Single Box Schematic.
See Figure 2-18.
1. Lay out the Seeder Harness on the Seeder Front
Frame Tube ensuring that the Electric Clutch 2-Pin
Connector is on the left side.
See Figure 2-17.
2. Rear RH side of the Seed Box, install a Spacer
w/Magnet between the 1
st
and 2
nd
Seed Cups. See
Figure 2-19. Remove the 2
nd
and 3
rd
Seed Meters
rear Round Head Machine Screw that mounts the
Seed Meter to the Seed Box and replace it with 1/4-20
x 1 Round Head Machine Screw. Place a 1/4 Flat
Washer on each side of the Sensor Mount and install
it on the 2
nd
and 3
rd
Seed Meter Screws. Secure with
Lock Washers and Nuts. Attach a Smart Shaft Sensor
to the Sensor Mount with sensor provided hardware
and #8-32 Flange Locknuts. Adjust the Smart Shaft
Sensor so that it is 1/8" Max away from the Spacer
w/Magnet on the Seed Shaft. Connect the Smart
Seed Shaft Sensor to the Seeder Harness.
3. Remove the .803 Knockouts in the front RH and LH
ends of the Seed Box.
4. On the inside at either end of the Seed Box install a Bin
Level Sensor Bracket with the Seed Box Mounting
3/8-16 Hardware.
See Figure 2-20. Determine the
desired level for the alarm to be indicated on the Brillion
Elite Mini Monitor and assemble the Bin Level Sensors
to Bin Level Sensor Brackets with sensor provided
hardware and #8-32 Flange Locknuts. If more
adjustment is needed, the Bin Level Sensor Brackets
can also be raised or lowered to the desired seed
level. Install Cord Grips from the inside of the Seed Box
out and secure with supplied Locknut on the outside of
the Seed Box. To get the Sensor Connector outside the
Seed Box, feed the terminals through the Cord Grip.
Install the terminals into the 3-Pin Shroud labeled “A”,
“B” and “C” as follows “A” White, “B” Black, “C” Green.
See Figure 2-15. Inside the Seed Box, add enough
slack to the Bin Level Sensor Cord to allow for future
adjustments of the Sensor. Secure the Bin Level Cord
by tightening the Cord Grip Compression Nut. Connect
both Bin Level Sensors to the Seeder Harness.
Figure 2-16: Bin Level Sensor Wire Detail
5. Install Pickup Switch Bracket with Clutch Shaft
Bearing Carriage Bolts, Lock Washer and Nut. See
Figure 2-21. Place Actuator Assembly onto the
Clutch Shaft, secure with Actuator Assembly Set
Screw. Assemble Smart Shaft Sensor onto the Pickup
Switch Bracket with sensor provided hardware and
#8-32 Flange Locknuts. Adjust the Smart Shaft
Sensor so that it is an 1/8" Max away from the
Actuator Assembly. Connect the Ground Speed
Smart Shaft Sensor to the Seeder Harness.
6. Unused Seeder Harness RH 3-Pin Connector needs
to be sealed with a 3-Pin Shroud and Cavity Plugs to
protect the Harness from the environment.
7. Connect the 240" Extensions Harness to the Seeder
Harness. Route the 240" Extension Harness along
the Seeder Frame and down the Drawbar/3-PT Hitch
to the Tractor.
8. Install Brillion Elite Mini Monitor on Tractor. See
“Brillion Elite Mini Monitor Tractor Installation -
Optional” on page 2-25.
9. If not already installed, install Smart Clutch Relay into
Elite Mini Tractor Harness 3-Pin Connectors.
10. Connect the Elite Mini Tractor Harness 14-Pin
Connector to Brillion Elite Mini Monitor, 3-Pin Power
Plug to 12 Volt Tractor Convenience Outlet and 6-Pin
Connector to the 240" Extension Harness. 4-Pin
Connector is not used at this time.
11. Bundle and secure all Harnesses along the Seeder
Frame and Drawbar/3-PT Hitch with Tie Wraps.
12. Program Bin Level Sensors and Smart Shaft Sensors
if not already pre-programmed. See Brillion Elite
Mini Monitor Chapter.
High Power Magnet in use. See “High Power
Magnet” on page 1-2.
White Wire
Black Wire
Green Wire
Terminal
3-Pin Shroud
Shroud Pin ID
Seal