Landoll 2211 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 74

background image

4-4

F-571-0511 Edition

OPERATION AND MAINTENANCE

Hydraulic Fold System (2211-13
& -15 Models Only)

1.

The Disc Chisel Disc is equipped with a hydraulic
fold system to raise and lower the wing frames for
narrow transport.

2.

Be sure the system is fully charged with hydraulic oil
before attempting to fold/unfold the unit. Air in the
system can allow uncontrolled dropping of the wing
frames causing serious personal injury or machine
damage. The system needs to be charged with oil
initially and any time the system has been opened for
repair such as cylinder, hose, or fitting
replacement/repair.

3.

To charge the system, carefully hitch the Disc Chisel
Disc to the tractor. Unpin the end(s) of the fold
cylinders, and position them so they can extend and
retract without contacting any frames or other parts.
Check the tractor hydraulic fluid level to make sure it
is full of the manufacturer’s recommended hydraulic
fluid. Connect the cylinder hoses to the tractor and
fully extend and retract the cylinders several times.
The cylinder rod travel should be smooth and
positive when all air has been purged from the
system. Due to large amounts of hydraulic oil
required, recheck the tractor fluid level to make sure
it is within proper operating limits.

4.

The hydraulic fold system is equipped with restrictors
in the rod end of cylinders to prevent uncontrolled
falling of wing frames when unfolding. Removal or
improper assembly of these restrictors can cause the
machine to fold improperly and result in serious
machine damage.



WARNING

Escaping hydraulic fluid can cause serious
personal injury. Relieve system pressure before
repairing, adjusting, or disconnecting. Wear
proper hand and eye protection when searching
for leaks. Use cardboard instead of hands (See
Figure 4-2.) Keep all components (cylinders,
hoses, fittings, etc.) in good repair.

«
...
50
51
52
53
54
...
»

Содержание 2211











































































Отзывы:

Нет отзывов

Похожие инструкции для 2211

Бренд: MacDon Страницы: 17

Бренд: Olympus Страницы: 50

Бренд: VAHVA Страницы: 19

Бренд: Panasonic Страницы: 180

Growers Supply 109722

Бренд: FarmTek Страницы: 9

Бренд: HANYOUNG NUX Страницы: 2

Бренд: Ofa Bamberg Страницы: 80

Бренд: Rainin Instrument Страницы: 16

Бренд: Quantum Страницы: 11

Бренд: Quanser Страницы: 21

Бренд: Quanser Страницы: 18

Бренд: Tactile Medical Страницы: 23

Бренд: Taarup Страницы: 72

Бренд: M-Audio Страницы: 48

Бренд: M-Audio Страницы: 19

Бренд: M-Audio Страницы: 17

Бренд: M-Audio Страницы: 18

Бренд: M-Audio Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды