Landoll 2211 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 74

background image

ASSEMBLY INSTRUCTIONS

3-27

Light Installation

NOTE

See Figures 2-1 through 2-4 for light bracket
placement. If no dimension is given for a bracket, it
should be located against frame member as shown in
drawing.

1.

Attach inner tail light mounting bracket supports to
the center frames using 1/2-13 x 8-1/2 hex head cap
screws, warning light bars, and hex lock nuts

Figure 3-24.)

2.

Attach outer LH and RH light brackets to frame
weldment using 1/2-13 x 9-1/2 hex head cap screws,
warning light bars, and hex lock nuts.

3.

Attach red brake lamps to inner tail light mounting
bracket supports and amber lamps to outer light
brackets using 1/4-20 x 1-1/4 hex head cap screws
and hex lock nuts.

4.

Mount enhanced lighting module on right hand tail
light bracket using #8-32 x 1/2 pan head slotted
screw and nuts. Connect rear harness to module and
connect the right/left side lights accordingly. Route
main wire harness through hose holder on hitch,
down the right side of the center frame and across
the back to the enhanced lighting module plug.

5.

Connect warning light harnesses to lights. Note that
2-24" harness extensions are required at the rear of
the main harness for adequate length.

6.

Attach SMV emblem and mounting bracket to rear
center frame bar using 1/2-13 x 5-1/2 hex head cap
screws, 1/4-20 x 3/4 hex head cap screws, and hex
lock nuts. The SMV sign should be centered on the
rear bar of the frame.

«
...
41
42
43
44
45
...
»

Содержание 2211











































































Отзывы:

Нет отзывов

Похожие инструкции для 2211

Бренд: CAMPAGNOLA Страницы: 4

Бренд: MADRIX Страницы: 12

Бренд: Narcotrend Страницы: 47

Бренд: Yamaha Страницы: 46

ST60+ SPEED INSTRUMENT

Бренд: Raymarine Страницы: 60

Бренд: Raymarine Страницы: 15

Бренд: RaycoWylie Страницы: 9

Бренд: Raven Страницы: 58

Бренд: Raven Страницы: 26

Бренд: Ravo Страницы: 114

Бренд: Alcoscan Страницы: 6

Бренд: M-Audio Страницы: 48

Бренд: M-Audio Страницы: 19

Бренд: M-Audio Страницы: 17

Бренд: M-Audio Страницы: 18

Бренд: M-Audio Страницы: 12

Бренд: M-Audio Страницы: 20

Бренд: York Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды