Landoll 2211 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 74

background image

OPERATION AND MAINTENANCE

4-7

Field Operation

1.

Raise the unit to take the weight off of the transport
locks. Remove the transport locks from the lift
cylinders. Store the transport locks on the retainers
above the main lift

(See Figure 4-7.)

Figure 4-7: Stored Transport Locks

Leveling (Front-to-Rear)

1.

The leveling feature on the Disc Chisel is used to
keep the machine level when raising the unit from a
working position to a transport position. The leveling
feature is also used to level the unit from front-to-rear
to perform a level operation in the field.

2.

The unit should be level from front to rear. This will
reduce horsepower requirements, allow a more
uniform tillage operation, and reduce unnecessary
point wear.

3.

To adjust the leveling feature, loosen jam nuts at
each end of the radius rod using the adjustment
wrenches provided on the hitch

(See Figure 4-8.)

To

raise the front of the Disc Chisel, lengthen the radius
rod assembly. To lower the front of the Disc Chisel,
shorten the radius rod assembly. After adjusting,
retighten jam nuts at each end. Adjustments should
be made in small increments.

Figure 4-8: Radius Rod Leveling Adjustment

stored trans lock

1-1/2 X 16 LOCKOUT

CYLINDER STOP
L-PIN

1/8 HAIRPIN

2211 level

HITCH RADIUS
ROD ASSEMBLY

ADJUSTMENT
WRENCHES

1-1/2 - 6 HEX
JAM NUTS

«
...
53
54
55
56
57
...
»

Содержание 2211











































































Отзывы:

Нет отзывов

Похожие инструкции для 2211

Бренд: ParaBody Страницы: 4

Бренд: NORLUX Страницы: 2

Бренд: Latchways Страницы: 80

Бренд: Kapriol Страницы: 28

SATURA SPOT LED PRO

Бренд: Elation Страницы: 41

Бренд: Tapco Страницы: 16

Бренд: Zenbooth Страницы: 40

Visium CytAssist

Бренд: 10x Genomics Страницы: 51

Chromium X Series

Бренд: 10x Genomics Страницы: 5

Бренд: Garelick Страницы: 2

Бренд: Gardico Страницы: 2

Бренд: OceanSat Страницы: 85

Бренд: Nemalux Страницы: 6

Бренд: OBDLink Страницы: 2

Бренд: Sagola Страницы: 62

Бренд: H&S Страницы: 54

Бренд: Samson Страницы: 2

Бренд: Yamaha Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды