Landoll 2211 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 74

background image

3-16

F-571-0511 Edition

ASSEMBLY INSTRUCTIONS

4.

Lift front gangs up under frame and install 1-7/16 x
6-3/8" pin on inner mount with roll pins

Figure 3-11.)

5.

Attach pivot block and orientate as shown so the
flanges are to the top and bottom. Slide gang from
the rear of the outer gang mounts into the front
position.

6.

Install the bushing and 1-8 x 6 hex head cap screw
and hex lock nut at the rear of the gang mount to
secure the gang assembly.

IMPORTANT

Make sure the hex lock nut is located on top of the
gang assembly.

7.

Install roll pins into the pin, disc angle. The 4" roll pin
will just go through the pin to act as a handle. The 2"
roll pin will be centered in the pin

(See Figure 3-12.)

Figure 3-11: Front Disc Gang Installation

Figure 3-12: Roll Pin Installation

3/8 x 4 ROLL
PIN

3/8 X 2 ROLL
PIN

1/4 HAIR PIN

BUSHING

1-8 X 6 HEX
HEAD CAP
SCREW

1” DISC ANGLE PIN

1-7/16 X 6-3/8
PIN

3/8 X 2-1/2
ROLL PIN

NOTE:
PIVOT BLOCK
ORIENTATION

1-8 HEX
LOCK NUT

2211 frt gang

3/8 x 4 ROLL
PIN

3/8 X 2 ROLL
PIN

1” DISC ANGLE PIN

roll pin installation

«
...
30
31
32
33
34
...
»

Содержание 2211











































































Отзывы:

Нет отзывов

Похожие инструкции для 2211

Бренд: EarthQuake Страницы: 28

Бренд: TAIKO Audio Страницы: 24

Бренд: PANDROL Страницы: 36

Бренд: Badger Basket Страницы: 7

Бренд: Backyard Discovery Страницы: 53

Бренд: Bante Instruments Страницы: 6

Бренд: Maico Страницы: 55

Бренд: Maico Страницы: 38

Бренд: Maico Страницы: 2

Бренд: MAHA Maschinenbau Haldenwang Страницы: 13

Бренд: Major tech Страницы: 12

Marathon Multi600

Бренд: Saeyang Страницы: 21

Бренд: S&C Страницы: 11

Бренд: V.ORLANDI Страницы: 144

Бренд: Tadano Страницы: 16

Zen-O lite RS-00600

Бренд: GCE Страницы: 20

SHAKER KEEPER 20V 200

Бренд: Garland Страницы: 84

Бренд: BRAND Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды