Landoll 2211 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 74

background image

OPERATION AND MAINTENANCE

4-13

Depth Stop Adjustment (Manual)

The operating depth of the Disc Chisel is controlled by a
single-point depth stop. The stop is located at the center
front of the machine.

1.

Adjust the depth stop by turning the handle in
(clockwise) to increase operating depth

Figure 4-12.)

Turn the handle out

(counter-clockwise) to decrease operating depth.

2.

The gauge on the side of the depth stop tube gives a
reference for depth setting. The “A“ setting refers to
maximum operating depth.

Figure 4-12: Depth Stop Adjustment (Manual)

Wheel Bearing Maintenance

Wheel bearing maintenance should be performed at the
beginning of every season of use. Check the wheel
bearings periodically for excessive end play. If needed,
adjust or replace them using the following procedure:
1.

Place the frame on blocks or stands sufficient to lift
the tire clear of the ground.

2.

Remove the tire.

3.

Remove the hub cap, cotter pin, slotted nut and
washer

(See Figure 4-11.)

4.

Remove the hub. Clean and inspect the bearings and
hub cavity. Replace any worn or defective parts.

5.

Repack the bearings using a high-quality wheel
bearing grease.

6.

Slide the seal(s) onto the spindle. Do not install the
seal into the hub. The 2211-09 & -11 models use (1)
triple lip seal. The 2211-13 & -15 models use (2)
single seals.

7.

Slide the inner bearing cone and hub onto the
spindle.

8.

Install the outer bearing cone, washer and slotted
nut.

9.

Tighten the slotted nut while rotating the hub until
there is a slight resistance to wheel rotation. Then,
back the slotted nut off one notch, until the wheel
rotates freely without end play.

10. Slide the seal to the hub and install the seal in the

hub.

NOTE

The triple-lip seals (2211-09 & -11) and both single seals
(2211-13 & -15) should point away from the hub to keep
contaminants out and allow grease to pass.

11. Install a new cotter pin and replace the hub cap.

Hydraulic Maintenance

1.

Check the tractor hydraulic fluid level per tractor
owners manual and after any leakage. Check fluid
level with the cylinders in the retracted position.

2.

If a cylinder or valve leaks, disassemble the parts to
determine the cause of the leak. Any time a cylinder
is opened up, or whenever any seal replacement is
necessary, it is advisable to clean all parts and
replace all seals. Seal kits are available from your
Landoll dealer.

3.

Check all hydraulic hoses weekly. Look for binding or
cracking. Replace all worn or defective parts
immediately.

DEPTH STOP TUBE

DEPTH STOP
GAUGE

DEPTH STOP
HANDLE

depth stop adjust op

«
...
59
60
61
62
63
...
»

Содержание 2211











































































Отзывы:

Нет отзывов

Похожие инструкции для 2211

Бренд: GE Страницы: 242

Бренд: GE Страницы: 24

Бренд: Balanced Body Страницы: 3

Бренд: York Fitness Страницы: 34

Бренд: Xoop Lighting Страницы: 20

Бренд: Vari Lite Страницы: 132

Бренд: DB Industries Страницы: 60

Бренд: vc999 Страницы: 55

Бренд: Salsbury Industries Страницы: 4

Бренд: Ocmis Irrigazione Страницы: 100

Бренд: Qlight Страницы: 4

Бренд: PAT Страницы: 44

Бренд: Park Tool Страницы: 4

Бренд: Park Central Страницы: 20

Бренд: Qlight Страницы: 4

Бренд: Uchida Yoko Страницы: 40

Бренд: Yamaha Страницы: 178

Бренд: Yamaha Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды