Landoll 2211 Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 74

background image

4-8

F-571-0511 Edition

OPERATION AND MAINTENANCE

Variable Ratio Adjustment

The leveler is equipped with a variable ratio adjustment.
This is located at the rear of the hitch and at the center of
the wheel lift where the leveler tube attaches. Connect
the leveler tube to the top hole in the center lift and the
top hole in the tongue for normal operation. This will
cause the rear of the machine to raise higher than the
front increasing transport height. The lower hole on the
center lift will not be used in normal operating conditions.

The adjustments can be set as follows:

Top hole in center lift, top hole in tongue - this will raise
the rear of the machine the highest.

Top hole in center lift, bottom hole in tongue - this will
lower the rear of the machine some, and raise the front.

1.

To change the variable ratio adjustment, lower the
implement to the ground and relieve the load on the
lift system.

2.

Extend or retract the radius rod, until the load is
removed from the leveler tower.

3.

Remove the 1-1/4-7 x 9-1/2 hex head cap screw,
slotted lock washer, and hex nut through the leveler
tower and hitch

(See Figure 4-9.)

4.

Reinstall the 1-1/4-7 x 9-1/2 hex head cap screw,
slotted lock washer, hex nut, and leveler tower in the
desired position. The radius rod will require some
adjustment to connect to the new position.

Figure 4-9: Variable Ratio Leveler Adjustment

ADJUSTMENT HOLES ON WHEEL LIFT

LEVELER TUBE

LEVELER
TOWER

HITCH RADIUS ROD

HITCH

HOLES ON
TONGUE

1-1/4-7 X 9-1/2 HEX
HEAD CAP SCREW,
SLOTTED LOCK WASHER,
AND HEX NUT

HITCH PIN,
1/2 X 2-1/4
SLOTTED
SPRING PIN,
AND 1-8 HEX
LOCK NUT

2210 var adj ratio op

«
...
54
55
56
57
58
...
»

Содержание 2211











































































Отзывы:

Нет отзывов

Похожие инструкции для 2211

Бренд: zipwake Страницы: 2

Бренд: zipwake Страницы: 2

Бренд: Makita Страницы: 60

Бренд: JB-Lighting Страницы: 60

Бренд: NEILPRYDE Страницы: 53

Бренд: JAC Страницы: 103

Бренд: 3Disc Страницы: 12

Бренд: B. Braun Страницы: 2

Aesculap Neurosurgery

Бренд: B. Braun Страницы: 13

Aesculap AdTec mini

Бренд: B. Braun Страницы: 2

Бренд: B.Well Страницы: 2

Бренд: B. Braun Страницы: 55

BA Ultimate LED

Бренд: B.A. International Страницы: 234

Бренд: Califone Страницы: 7

Бренд: CALITEK Страницы: 16

Бренд: LAHTI PRO Страницы: 20

Бренд: LAHTI PRO Страницы: 16

Бренд: J&M Страницы: 53

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды