Landoll 2211 Скачать руководство пользователя страница 35

Страница: 35 / 74

ASSEMBLY INSTRUCTIONS

3-19

Figure 3-16: Disc Gang Height Adjustment

11. Connect the front gangs to the radius rods with a 1-8

x 5-1/2 hex head cap screw. Before tightening the
front gangs, adjust the gang height as shown in

Figure 3-16

to 17" from the bottom of the frame to

the top of the disc blades.

12. Once this dimension is set, tighten jam nuts on the

front radius rods.

13. The rear radius rods are adjustable and once

installed with a 1-8 x 5-1/2 hex head cap screw
should be set to 16" from the bottom of the frame to
top of disc blade for initial operation.

Auto Reset Shank and Shovel
Installation

Attach each shank assembly to each clamp
assembly using 3/4-10 x 5 hex head cap screw in the
top hole, 3/4-10 x 4 hex head cap screw in the
bottom hole, and hex lock nuts.

NOTE

For shallower depths, it may be necessary to move
shank into upper mounting holes. For certain conditions
shank may also be rotated forward.

Install 2 x 1 x 18 spike to each shank using 1/2-13 x 3
hex head cap screws, flat washers, and heavy hex
nuts

(See Figure 3-15.)

16”

17”

disc gang height

NOTE: DISC GANG CYLINDER IS FULLY RETRACTED.

Содержание 2211











































































Результаты поиска

Содержание 2211

Отзывы:

Похожие инструкции для 2211

Бренды по названию

Популярные бренды

Landoll 2211, Руководство оператора

Результаты поиска

Содержание 2211

Отзывы:

Похожие инструкции для 2211

Бренды по названию

Популярные бренды