Landoll 2211 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 74

background image

OPERATION AND MAINTENANCE

4-3

Hydraulic Lift System

The Disc Chisel is equipped with a hydraulic lift system to
raise and lower the unit in the field.



WARNING

Figure 4-2: Hydraulic Leak Detection

Figure 4-3: Installed Transport Locks

1.

The hydraulic lift system contains cylinders plumbed
together. It is important that the cylinders be
connected in the proper series for the lift system to
operate correctly.

2.

The hydraulic system is not filled with oil and should
be purged of air before transporting and field
operations. Carefully hitch the Disc Chisel to the
tractor and connect the hydraulic lift hoses. Check to
make sure the tractor hydraulic reservoir is full of the
manufacturer’s recommended oil. Slowly raise the
machine. With all cylinders fully extended remove the
1-1/2 X 16 transport lockouts

(See Figure 4-3.)

Store

transport lockouts as shown in

Figure 4-4.

Lower

and raise the unit to verify that cylinders are working
simultaneously throughout the stroke. Do not loosen
any hoses or fittings. Recheck tractor reservoir to
make sure it is within operating limits.

Figure 4-4: Stored Transport Locks

Escaping hydraulic fluid can cause serious
personnel injury. Relieve system pressure before
repairing, adjusting, or disconnecting. Wear
proper hand and eye protection when searching
for leaks. Use cardboard instead of hands (See
Figure 4-2.) Keep all components (cylinders,
hoses, fittings, etc.) in good repair.

1-1/2 X 16
LOCKOUT

CYLINDER
STOP L-PIN

1/8 HAIRPIN

installed trans lock

stored trans lock

1-1/2 X 16 LOCKOUT

CYLINDER STOP
L-PIN

1/8 HAIRPIN

«
...
49
50
51
52
53
...
»

Содержание 2211











































































Отзывы:

Нет отзывов

Похожие инструкции для 2211

Бренд: Wavetek Страницы: 74

Бренд: Fairchild Страницы: 16

Бренд: Cameo Страницы: 64

Бренд: Cameo Страницы: 100

Бренд: CAME Страницы: 32

Бренд: Palmako Страницы: 83

So-exercise TX7

Бренд: T-SoX Страницы: 8

Бренд: Meritor Страницы: 65

MT765 Challenger

Бренд: Fast Страницы: 31

Бренд: Taurus Страницы: 38

Бренд: Phonocar Страницы: 12

Бренд: Spokey Страницы: 4

Бренд: Billy Goat Страницы: 14

ARIEDO HDC 300W

Бренд: GSi Страницы: 28

Бренд: Nippon Genetics Страницы: 14

Groline HI981412

Бренд: Hanna Instruments Страницы: 44

Бренд: Honestech Страницы: 43

Бренд: KaVo Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды