lancer bridge tower Скачать руководство пользователя страница 5

5

4. 

Twist the key-lock rod, located behind the splash plate, to 

unlock the head of the tower. 

A. Key-Lock Rod

A

5.  Once unlocked, lift the head of the tower all the way then 

lock the head of the tower in place by using the kick stand 

next to the tower hinges. 

C

B

A. Kickstand

B. Tower Hinges

C. Front Panel

A

6.  Press one of the top retaining clips, located on the inside of 

the front panel, and simultaneously pull forward on the panel 

to unhook from the retaining clip. Repeat for remaining three 

front retaining clips.

 

Make sure, when removing the front panel, to pull 

straight out. DO NOT bend plastic when removing the 

panel, this could damage the retaining clips. 

ATTENTION

7. 

Slide the front panel off of the dispenser by leaning the top of 

the panel forward then slide off of the dispenser.

C

C

B

A. Front Panel

B. Back Panel

C. Retaining Clips

A

8.  Route tubing from the CO

2

 inlet at the remote chiller and 

normal, non-diet syrup pumps and connect both lines to  one 

of the low pressure CO

2

 regulator manifold outlets.

A

B

C

D

A. Line to Non-Diet Syrup 

    Pumps

B. Line to Diet Syrup Pumps

C. Line to CO

2

 Regulator

D. CO

2

 Regulator Manifold

9.  Connect tubing routed from the diet syrup pumps to the   

second outlet of the low pressure CO

2

 regulator manifold.

10.  Turn on the water supply.
11. 

Verify all Bag-in-Box contain syrup and check for leaks.

12.  Open the pressure relief valve located on the remote chiller 

system by flipping up on the valve cap lever. Hold open until 

water flows from the relief valve then close (flip down) relief 

valve.

13.  Connect power cord to grounded electrical outlet. 

A. Press Retaining Clip

A

 

The dispenser must be properly electrically grounded 

 

to avoid serious injury or fatal electrical shock. The 

 

power cord has a three-prong grounded plug. If a 

 

three-hole grounded electrical outlet is not available, 

use an approved method to ground the unit. Follow all 

local electrical codes when making connections. Each 

 

dispenser must have a separate electrical circuit. Do 

 

not use extension cords. Do not connect multiple

 

electrical devices on the same outlet.

WARNING

Содержание bridge tower

















Отзывы: