manualshive.com logo in svg

lancer bridge tower, Руководство по установке

Поделиться
Скачать
lancer bridge tower Скачать руководство пользователя страница 16

Lancer Corp.

800-729-1500

Technical Support/Warranty: 800-729-1550

[email protected]

lancercorp.com

PLUMBING DIAGRAM

Item 

Description

S1  

Syrup Line 1

S2  

Syrup Line 2

S3  

Syrup Line 3

S4  

Syrup Line 4

S5  

Syrup Line 5

S6  

Syrup Line 6

S7  

Syrup Line 7

S8  

Syrup Line 8

S9  

Syrup Line 9

S10 

Syrup Line 10

PW 

Plain Water Line

SD 

Soda Line

RC  

Recirculation Line

S1

S7

S3

S8

S4

SD

PW

S9

S5

RC

S2

S10

S6

S1

SD PW

S3

S4

S5

S6

S7

S8

S9 S10

S2

Video Codec Notice:

THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE PERSONAL USE OF A CONSUMER OR OTHER USES IN WHICH IT DOES NOT RECEIVE REMUNERA-

TION TO (i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD (“AVC VIDEO”) AND/OR (ii) DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL 

ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL 

INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE 

HTTP://WWW.MPEGLA.COM

 

Third Party Software Notice:

This product contains third party licensed software components.  These licenses may be viewed in the Service Menu under Component Versions.  Where specific license terms entitle you to the source 

code of such software, source code files and corresponding licenses are provided with the binaries.  Available sources can be found in the ‘sources’ directory on the second partition of the memory card 

in the display assembly. This software is distributed WITHOUT ANY WARRANTY. While you are free to modify and install software licensed under the GNU General Public License (GPL) or GNU Lesser 

General Public License (LGPL), Lancer does not provide technical support or warranty service for equipment running modified software.

Trademarks:

Hangul text is displayed using the font Baekmuk Batang. Baekmuk Batang, Baekmuk Dotum, Baekmuk Gulim, and Baekmuk Headline are registered trademarks owned by Kim Jeong-Hwan.

Содержание bridge tower

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды