Lagler Flip страница 16 Скачать руководство пользователя

Страница: 16 / 60

FLIP

01.12.2012

English / Englisch

WORKING WITH THE FLIP

5.1 GENERAL APPLICATION TIPS

WARNING!

RISK OF DEATH from electrical shock:

The machine may never be used for wet processing opera-
tions of any kind!

ATTENTION!

•

Bear in mind that the FLIP

operates at very high cutting

speeds! For this reason, there is a risk of burn marks for
finer grit grades!

•

Do not apply excessive pressure to the attachment while
sanding! This will significantly worsen the sanding finish
by causing deep scratches or burn marks and could cause
the motor to switch off from overheating!

The FLIP

is a very versatile machine. The attachment can be

changed in a matter of seconds. The FLIP

is used for the sanding

of transitions, borders, edges, corners and stairs.

•

Deep sanding marks due to the selection of a too coarse grit

grade can be prevented by starting the first sanding operation

with the finest grit grade possible.

•

Prevent sanding marks made by previously used grit grade by

adhering to the order of the sandpaper grit grade and never

skip more than one grit grade.

•

After replacing the sanding disc, start working in poorly lit

areas of the room in order to remove the initial aggressive-

ness of the sanding medium.

•

Always vacuum the floor or stairs thoroughly before the first

sanding operation and after each additional one.

•

Clean the wheels of the machine regularly.

Working with the FLIP

Fig. 9

Guide the FLIP

with both hands.

NOTE:

For more information free of charge, please

contact: within Germany

- Telephone: 0800 / 52 34 537

- Fax:

0800 / 48 66 353

within the USA

- Telephone: 800-848-6635

- Telephone: 0049 - 7135 - 98 90 - 0

- Fax:

0049 - 7135 - 98 90 - 98

- e-mail:

[email protected]

- Internet:

http://www.laegler.com

You will also find important and interesting

application tips in the LÄGLER

application

technique guidelines “Sanding Wooden

Floors” (http://www.laegler.com)!

Содержание Flip





























































Результаты поиска

Содержание Flip

Отзывы:

Похожие инструкции для Flip

Бренды по названию

Популярные бренды

Lagler Flip, Эксплуатация Обслуживание Безопасность

Результаты поиска

Содержание Flip

Отзывы:

Похожие инструкции для Flip

Бренды по названию

Популярные бренды