Lagler Flip страница 25 Скачать руководство пользователя

Страница: 25 / 60

FLIP

01.12.2012

English / Englisch

An inspection of the machine can be conducted quickly and prevents

the necessity of later complaints which can be caused by small

damages to the machine or by worn-out parts. These measures

contribute significantly to the preservation of the value of the ma-

chine and, ultimately, to your own safety.

7.1 CLEANING AND CARE

WARNING!

RISK OF FIRE from spontaneous combustion and the formation
of sparks while sanding:

•

There is a high risk of fire when sanding woods with a
large amount of resin, waxed floors or metal!

•

Therefore, the machine must always be cleaned carefully
directly after sanding!

•

Be certain to note the warning notices of the paint, oil and
wax manufacturers!

The following maintenance measures should be conducted before

beginning work to ensure the proper functionality of the machine

and the usual first-class sanding results.

•

Clean the wheels of the machine.

•

Check the tension of the V-belt and/or correct this (

Section

7.2, Tightening the V-belt

•

Clean the paper tensioning screw and the thread of the sand-

ing plate regularly. Otherwise the thread will be damaged.

•

Check the dust suction system and the dust bag for leaks and

damages.

•

Conduct a visual inspection of the electrical equipment

(rocker switch, extension cable, plug, couplers).

MAINTENANCE WORK AND REPLACEMENT OF WEARING PARTS

Содержание Flip





























































Результаты поиска

Содержание Flip

Отзывы:

Похожие инструкции для Flip

Бренды по названию

Популярные бренды

Lagler Flip, Эксплуатация Обслуживание Безопасность

Результаты поиска

Содержание Flip

Отзывы:

Похожие инструкции для Flip

Бренды по названию

Популярные бренды