Lagler Flip страница 43 Скачать руководство пользователя

Страница: 43 / 60

FLIP

01.12.2012

English / Englisch

This section shows you how to remedy possible malfunctions. If

none of the measures listed here are successful, please contact

our service department, your retailer or your importer.

THE MACHINE DOES NOT RUN

The machine does not start

•

The machine is not connected to the electrical network. Check

the following items:

- Is the motor cable connected to the extension cable?

- Is the extension cable inserted into the power socket?

•

The power socket is not properly connected. This error must

be corrected by a professional.

•

The electrical safety device of the electrical network inter-

rupted the electrical circuit, e.g. because

- too many electricity consumers are connected to the same

electrical circuit,

- improper electrical installation.

The causes for the error must be repaired by an expert.

•

The electrical network is not providing sufficient voltage

(undervoltage). Use a transformer if necessary (e.g. LÄGLER

part number 708.00.00.100 for 230 volts).

•

The temperature switch in the motor has switched off the

machine because

- one or more power cables have a total length of more than

20 m,

- the power cable has wire cross-sections which are too

small (wire cross-sections smaller than 1.5 mm²),

- or too much pressure was applied to the attachment while

sanding.

The motor must cool off and the causes for the problems

named above must be remedied.

•

An electrical component of the machine (e.g. cable, switch)

is defective and must be inspected by an electrician and

replaced if necessary.

Causes of faults

CAUSES OF FAULTS

WARNING!

RISK OF DEATH from electrical shock:

Work on the electrical equipment is to
be conducted exclusively by a qualifi ed
electrician (circuit diagram in

Section 10

The machine must be switched off and the
power plug removed from the socket dur-
ing this work!

RISK OF INJURY due to unsuitable parts:

Make sure that only original LÄGLER

spare parts and original LÄGLER

acces-

sories are used!

Содержание Flip





























































Результаты поиска

Содержание Flip

Отзывы:

Похожие инструкции для Flip

Бренды по названию

Популярные бренды

Lagler Flip, Эксплуатация Обслуживание Безопасность

Результаты поиска

Содержание Flip

Отзывы:

Похожие инструкции для Flip

Бренды по названию

Популярные бренды