Lada Kalina Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 168

background image

In case you stay the wiper switch

lever not in the position I and switch
the ignition off for more than 1
minute, then after switching the igni-
tion on the wiper doesn’t work till the
lever position is changed or till wash-
er is switched on.

To remove stains, road salt coat or

road surface elements you are to
clean the blades with the washer
tank fluid periodically.

The fat, wax, insects and etc.

availability in the windshield can lead
to the wipers hunting and dirty stains
appearance at the windshield.

In case stains can’t be removed

with the washer fluid you are to clean
the windshield exterior surface and
blades with the soft textile and spe-
cial cleaning agent.

After cleaning wash the wind-

shield and blades with water.

ATTENTION!

1. To prevent damage, do not

use the windshield wiper with the
bonnet opened.

2. Do not switch on the wiper

when the windshield is dry. This
may result in scratches on the
window or damage the wiper
blades. Before switching on the

wipers in dry window always use
the window washer.

3. If wiper blades are frozen to

the window, before switching on
the wiper you should first switch
on windshield heating (in the
design variant see the section
«Ventilation and heating modes»)
and make sure that the wiper
blades have thawed.

Attempt to switch on the wipers

with blades frozen to the window
can lead both to damage to rub-
ber tape of blades, and to early
wear of the wiper drive.

4. Do not clean the wiper

blades with petrol or solvent, it
will damage them.

4

Р.Э.-21920, англ. яз.

49

«
...
49
50
51
52
53
...
»

Содержание Kalina









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Kalina

Бренд: ZAPTEC Страницы: 64

Бренд: ZAPTEC Страницы: 24

Бренд: TATA Motors Страницы: 94

Бренд: GÄN Страницы: 24

Бренд: IAME Страницы: 17

Бренд: iArmor Страницы: 6

Бренд: Kolpin Outdoors Страницы: 6

Бренд: Schartec Страницы: 2

Бренд: Thule Страницы: 8

STEALTH POWER RBP-216-SP

Бренд: RBP Страницы: 16

STREET SUPER SHIFTER

Бренд: HURST Страницы: 2

Бренд: Audiovox Страницы: 3

Бренд: Victory 4x4 Страницы: 9

Бренд: Oypla Leisure Страницы: 4

Бренд: Joie Страницы: 53

Бренд: Prorack Страницы: 15

Бренд: RAM Страницы: 5

Бренд: Curt Group Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды