Laars mascot ft MFTHW Скачать руководство пользователя

Страница: 66 / 96

LAARS Heating Systems

Page 64

5.9 Outdoor Reset Adjustment

5.10 External Set Point Temperature Contro

Outdoor Reset varies the control setpoint based on

the outdoor temperature. The reset function works

as shown in Figure ‘CH Outdoor Reset’. When the
outdoor air temperature reaches

4:OH

“high outdoor

temperature setpoint”, the control point setting is
adjusted to

7:cL

“low boiler temperature setpoint”.

When the outdoor air temperature reaches

5:OL

“low

outdoor temperature setpoint” the control setpoint is
adjusted to

6:cH

“high boiler temperature”.

Default outdoor reset setpoint is 100°F (38°C)

A signal from a building management system may be connected to the appliance to enable remote

control. This signal should be a 0-10 volt DC signal. When this input is enabled, a building control

system can be used to control the set point temperature of the appliance.

The control interprets the 0-10 volt signal as follows; when the signal is between 0 and 1.5 volts, the

appliance will be in standby mode, not firing.

When the signal rises above 1.5 volts, the appliance will ignite. As the signal continues to rise
towards its maximum of 10 volts, the appliance will increase in set point temperature. Adjust

6:cH

and

7:cL

to set MIN and MAX boiler water temperatures respectively.

Connect a building management system or other auxiliary control signal to the terminals marked

for this purpose on the appliance terminal block (shown in Piping Diagrams, this manual). Caution

should be used to ensure that the 0-10 VOLT + connection does not become connected to ground.

Connect to terminal strip as outlined 4.17 Electrical Connections.

NOTE: 0 - 10VDC terminals may not be used for both outdoor reset and 0 - 10VDC temp

setpoint simultaneously.

The Outdoor Temperature Mode Icon on the display

will flash if an Outdoor Sensor or 0-10 Volt is not

connected to the appliance.

See

Figure 15

to set your Outdoor Reset. To check

the CH Target Temperature while using Outdoor

Temperature Mode,
Press the

button while the appliance is

operational and the display panel is powered on.

Connect to terminal strip as outlined 4.17 Electrical Connections.

NOTE: 0 - 10VDC terminals may not be used for both outdoor reset and 0 - 10VDC temp

setpoint simultaneously.

Figure 15.

Outdoor Reset

Operating condition

(warm weather shutdown)

Содержание mascot ft MFTHW

































































































Результаты поиска

Содержание mascot ft MFTHW

Отзывы:

Похожие инструкции для mascot ft MFTHW

Бренды по названию

Популярные бренды

Laars mascot ft MFTHW, Инструкция по установке и эксплуатации

Результаты поиска

Содержание mascot ft MFTHW

Отзывы:

Похожие инструкции для mascot ft MFTHW

Бренды по названию

Популярные бренды