Laars mascot ft MFTHW Скачать руководство пользователя

Страница: 78 / 96

LAARS Heating Systems

Page 76

8.2 Flushing the Boiler

- Flushing the Boiler

Flushing the Heat Exchanger of boiler is a complicated procedure. Refer to the following instructions carefully

before attempting the procedure. If you do not understand about the procedure, contact an authorized techni-

cian or licensed professional. Keep in mind that improper maintenance can void your warranty.

1. Disconnect electric power to the boiler.

2. Close the shutoff valves on both hot water outlet

and cold water inlet lines. (V1 & V2)

3. Connect one hose “D1” to the valve “V3” and

place the free end in the bucket. Connect one

of the hoses “D3” to the circulation pump outlet

and the cold water inlet line at the valve “V4”.

Connect other hose “D2” to the circulation pump

inlet and place the free end in the bucket.

4. Pour the cleaning solution into the bucket.

Place the drain hose (D1) and the hose (D2) to the

pump inlet into the cleaning solution.

5. Open service valves (V3 & V4) on the hot water

outlet and cold water inlet lines.

6. Turn on the circulation pump (Operate the pump and

allow the cleaning solution to circulate through the

boiler for at least 1 hour at a rate of 4 gallons per

minute.)

7. Rinse the cleaning solution from the boiler as follows:

- Remove the free end of the drain hose (D1) from

the bucket.

- Close service valve, (V4), and open shut off valve,

(V2).

Do not open shut off valve, (V1).

- Allow water to flow through the boiler for 5 minutes.

- Close shut off valve (V2).

8. Disconnect all hoses.

9. Remove the cold water inlet filter from the boiler and

clean out any residues.

10. Reinsert the filter and ensure the filter cap is

securely tightened.

11. Connect electrical power to the boiler.

Содержание mascot ft MFTHW

































































































Результаты поиска

Содержание mascot ft MFTHW

Отзывы:

Похожие инструкции для mascot ft MFTHW

Бренды по названию

Популярные бренды

Laars mascot ft MFTHW, Инструкция по установке и эксплуатации

Результаты поиска

Содержание mascot ft MFTHW

Отзывы:

Похожие инструкции для mascot ft MFTHW

Бренды по названию

Популярные бренды