Laars mascot ft MFTHW Скачать руководство пользователя

Страница: 77 / 96

Mascot FT, Heating Only, Boiler

Page 75

8.1 Annual startup & general maintenance

- Check the air vent

If the air vent valve seems to work freely without

leaking, replace cap “A” by twisting all the way on.

Loosen cap “A” one turn to allow vent to operate.

If vent does not operate correctly, replace the vent.

Maintenance procedures [Every 6 Months]

- Check the boiler piping (gas and water)

Visually inspect for leaks around internal water

piping. Also inspect external water piping,

circulators, relief valve and fittings. Immediately

call a qualified service technician to repair any

leaks. Leaks must be fixed by a qualified service

technician immediately.

Failure to comply with this instruction could result in

severe personal injury, death or substantial property

damage.

- Check the operate relief valve

Before proceeding the procedures, verify that relief

valve outlet has been piped to a safe place of

discharge, avoiding any possibility of scalding from

hot water. If water flows freely, release the lever

and allow the valve to seat. Watch the end of the

relief valve discharge pipe to ensure that the valve

does not weep after the line has had time to drain.

If the valve weeps, lift the seat again to attempt

to clean the valve seat. If the valve continues to

weep, contact your qualified service technician for

inspecting the valve and system. If water does not

flow from the valve even though you have lifted the

- Check the burner state

You can clean the exterior of burner. However, if you

need to clean the inside of the burner stage, you

should call an expert.

WARNING

Leaks must be fixed by a qualified service technician

immediately. Failure to comply with this instruction

could result in severe personal injury, death or

substantial property damage. This discharge line

must be installed by a qualified heating

installer or a service technician.

lever completely, the valve or discharge line may be

blocked. Shut down the Boiler immediately. Call your

qualified service technician to inspect the boiler and

system.

Содержание mascot ft MFTHW

































































































Результаты поиска

Содержание mascot ft MFTHW

Отзывы:

Похожие инструкции для mascot ft MFTHW

Бренды по названию

Популярные бренды

Laars mascot ft MFTHW, Инструкция по установке и эксплуатации

Результаты поиска

Содержание mascot ft MFTHW

Отзывы:

Похожие инструкции для mascot ft MFTHW

Бренды по названию

Популярные бренды