Laars mascot ft MFTHW страница 14 Скачать руководство пользователя

Страница: 14 / 96

LAARS Heating Systems

Page 12

SECTION 3

Safety Regulations

3.1 Safety Symbols

WARNING

To avoid product damage, personal injury, or even

possible death, carefully read, understand, and

follow all the instructions in the Installation and

Operation manual before installation, operation

and service the Boiler.

Laars cannot anticipate every circumstance

that might involve a potential hazard. Therefore,

all possible incidents are not included in our

warnings. Proper installation, operation, and

service are your responsibility. You must make

sure that the operation and settings of the Boiler

are safe for you and for others.

This manual provides Safety Symbols. When the

user fails to adhere to the following requirement,

it may cause death, serious injury, and substantial

property damage.

For safety symbols, ‘DANGER’, ‘WARNING’,

CAUTION’ are indicated and the definitions for these

terms are as follow:

DANGER

Indicates an imminently hazardous situation

which, if not avoided, will result in death or

serious injury. This signal word is limited to the

most extreme situations.

WARNING

Indicates a potentially hazardous situation

which, if not avoided, could result in death or

serious injury.

CAUTION

Indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderate injury. It is also used to alert against

unsafe practices and hazards involving only

property damage.

FOR YOUR SAFETY READ BEFORE

OPERATING

If you do not follow these instructions exactly, a

fire or explosion could result causing property

damage, personal injury or loss of life.

A. This appliance does not have a pilot. It

is equipped with an ignition device which

automatically lights the burner. Do not try to

light the burner by hand.

B. BEFORE OPERATING smell all around the

appliance area for gas. Be sure to smell next

to the floor because some gas is heavier than

air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do not use any

phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the

fire department.

C. Use only your hand to push in or turn the gas

control knob. Never use tools. If the knob will

not push in or turn by hand, don’t try to repair

it, call a qualified service technician. Force

or attempted repair may result in a fire or

explosion.

D. Do not use this appliance if any part has

been under water. Immediately call a qualified

service technician to inspect the appliance and

to replace any part of the control system and

any gas control which has been under water.

This appliance must be installed in accordance with

local codes if any; if not, follow ANSI Z224.1/NFPA

54 or CAN/CSA B149.1, Natural Gas and Propane

Installation Code, as applicable.

This appliance is certified for use at altitudes up

to 4,500ft(1,370m) in accordance to the latest CSA/

CGA 2.17-M91 Gas-Fired Appliances for Use at

High Altitudes.

Содержание mascot ft MFTHW

































































































Результаты поиска

Содержание mascot ft MFTHW

Отзывы:

Похожие инструкции для mascot ft MFTHW

Бренды по названию

Популярные бренды

Laars mascot ft MFTHW, Инструкция по установке и эксплуатации

Результаты поиска

Содержание mascot ft MFTHW

Отзывы:

Похожие инструкции для mascot ft MFTHW

Бренды по названию

Популярные бренды