Laars mascot ft MFTHW Скачать руководство пользователя

Страница: 20 / 96

LAARS Heating Systems

Page 18

The Mascot FT is standard as a Natural Gas Boiler

and must be converted if propane is the desired gas,

unless specifically manufactured for propane.

Adequate drainage

• The appliance should be installed not to damage

the adjacent area. If such locations cannot be

avoided, it is recommended that a suitable drain

pan, adequately drained, be installed under the

appliance. The pan must not block combustion air

flow.

Connecting the Water Supply

• To conserve water and energy, insulate all water

piping—especially the hot and recirculation water

lines. Never cover the drain or pressure relief valve.

Having a backflow preventer in the cold water

supply line will prevent thermal expansion

backflow. Contact the water supplier or local

plumbing inspector for information about how to

control this situation.

If overheating occurs or the gas supply fails to shut

off, turn off the manual gas valve.

This installation must conform with below section

• “Air for Combustion and Ventilation” of the

National Fuel Gas Code, ANSI Z224.1/NFPA 54,

or Sections 8.2, 8.3 or 8.4 of Natural Gas and

Propane Installation Code, CAN/CSA B149.1, or

applicable provisions of the local building codes.

CAUTION

NOTICE

The instructions for the installation of the venting

system shall specify that the horizontal portions of

the venting system shall be supported to prevent

sagging; the methods of and intervals for support

shall be specified. These instructions shall also

specify that the venting system:
Category I, II and IV boilers must be installed so

that horizontal sections have a slope of at least ¼

inch per foot (21 mm/m) to prevent accumulation of

condensate; and

For Category II and IV boilers, where necessary,

have means provided for drainage of condensate.

AVIS

Les instructions d'installation du système

d'évacuation doivent préciser que les sections

horizontales doivent être supportées pour prévenir

le fléchissement. Les méthodes et les intervalles

de support doivent être spécifiés. Les instructions

doivent aussi indiquer les renseignements suivants:

les chaudières de catégories I, II et IV doivent

présenter des tronçons horizontaux dont la pente

montante est d'au moins ¼ po par pied (21 mm/m)

entre la chaudière et l'évent; les chaudières de

catégories II et IV doivent être installées de façon à

empêcher l'accumulation de condensat;
et si nécessaire, les chaudières de catégories II et IV

doivent être pourvues de dispositifs d'évacuation du

condensat.

Содержание mascot ft MFTHW

































































































Результаты поиска

Содержание mascot ft MFTHW

Отзывы:

Похожие инструкции для mascot ft MFTHW

Бренды по названию

Популярные бренды

Laars mascot ft MFTHW, Инструкция по установке и эксплуатации

Результаты поиска

Содержание mascot ft MFTHW

Отзывы:

Похожие инструкции для mascot ft MFTHW

Бренды по названию

Популярные бренды