KYLAND Technology PTS-DR200 Скачать руководство пользователя | Manualshive

Страница: 6 / 55

background image

Kyland Technology (Shanghai) Co., Ltd PTS-DR200 Time Server

- 4 -

1.

Basic Features

1.1.

Introduction

[Figure 1-1] PTS-DR200 Time Server

PTS-DR200 is a multifunction time server. PTS-DR200 is designed for DIN Rail Mount
requirements. It is a compact and provides nanosecond accuracy time service for any
industry fields. It supports GPS (Global Positioning Service), BDS (Chinese Satellite
System), and GLONASS (Russian Satellite System) as sky time sources and IEEE1588
PTP (Precision Timing Protocol), IRIG-B as ground time sources. Based on the multiple
time source input PTS-DR200 has multi-time source selection logical and Sky-
Grounding time backup function inside. It also supports IEEE1588 PTP (Precision
Timing Protocol), NTP (Network Time Protocol), IRIG-B, 1PPS, 1PPM, 1PPH and TOD
etc. time synchronization signal output as time synchronization purpose. PTS-DR200
supports TMS (Time Management System) features to report PTS-DR200 time status
by IEC61850, IEC60870-5-104, SNMP, Modbus TCP, and DNP over TCP etc. It also can
generate accurate GOOSE signal to trigger an event to monitor IED time status in
power system and provides GOOSE subscriber to send time status by IEC61850 MMS.
The default embedded WEB service provides system management and also optional
support SNMP management.

«
...
4
5
6
7
8
...
»

Содержание PTS-DR200
























































Отзывы:

Нет отзывов

Похожие инструкции для PTS-DR200

AC Motor Drives VFD-XXXE

Бренд: Delta Страницы: 36

SmartPAC PRO 4353001

Бренд: Wintriss Страницы: 6

Бренд: IBM Страницы: 286

Бренд: ZIGBEE Страницы: 66

Бренд: Zonet Страницы: 34

Бренд: MaxTech Страницы: 14

Бренд: MaxTech Страницы: 16

Бренд: TRENDnet Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды