KYLAND Technology PTS-DR200 Скачать руководство пользователя

Страница: 27 / 55

Kyland Technology (Shanghai) Co., Ltd PTS-DR200 Time Server

- 25 -

Items

Parameters

Description

Set stop time to define what time to start DST.
Format is 24 hours format.
Range is between 00:00 and 24:00.
Default value is 00:00.

The Daylight Saving Time (DST) will define by what month,

week, day and time to stop.

Press ‘Save’ button to save the current setting when you change setting.

3.5.3. NTP Settings

Press ‘NTP’ on the left navigation bar to show NTP setting screen.
The NTP setting screen will be shown as:

[Figure 3-16] NTP Setting Screen

Table 15 – NTP Setting

Items

Parameters

Description

NTP Server

Enable

Disable

Activate NTP server feature.
Enable: Make NTP server start working;
Disable: Make NTP server stop working.

NTP UTC Offset

0.00H

Set time offset between NTP time stamp and UTC. If NTP time
stamp needs time offset, please set this parameter.
Unit is Hour(H);
Range is between -12H and 12H.
Default value is 0.00H.

Press ‘Save’ button to save the current setting when you change setting.

3.5.4. PTP Settings (Optional)

Press ‘PTP’ on the left navigation bar to show PTP setting screen.
The PTP setting screen will be shown as:

Содержание PTS-DR200
























































Результаты поиска

Содержание PTS-DR200

Отзывы:

Похожие инструкции для PTS-DR200

Бренды по названию

Популярные бренды

KYLAND Technology PTS-DR200, Руководство по эксплуатации

Результаты поиска

Содержание PTS-DR200

Отзывы:

Похожие инструкции для PTS-DR200

Бренды по названию

Популярные бренды