KYLAND Technology PTS-DR200 Скачать руководство пользователя

Страница: 11 / 55

Kyland Technology (Shanghai) Co., Ltd PTS-DR200 Time Server

- 9 -

APP 0707
14:55:10

[Figure 2-8] PTS-DR200 Application Information

2.4.

Indicator Lights

The Screen has two lines to indicate system information.

Table 4 – Indicator Light Definition

Name

Definition

Status

Description

ALARM

System Alarm

Device is abnormal.

Off

Device is normal.

LOCK

Time Lock

Flash(1 second)

Clock is LOCK status.

Flash(3 seconds) Clock is HOLD status.
Off

Clock is initializing.

FIX

Satellite Position Fix

Position fix is 3D type.

Off

Position fix is invalid.

ANT

Antenna Status

Antenna is normal.

Off

Antenna is abnormal.

The enclosure is one part of the whole cooling system. Don’t cover it when it works.
The picture of Manual is only schematic. Please refer to real device.

Содержание PTS-DR200
























































Результаты поиска

Содержание PTS-DR200

Отзывы:

Похожие инструкции для PTS-DR200

Бренды по названию

Популярные бренды

KYLAND Technology PTS-DR200, Руководство по эксплуатации

Результаты поиска

Содержание PTS-DR200

Отзывы:

Похожие инструкции для PTS-DR200

Бренды по названию

Популярные бренды