KYLAND Technology PTS-DR200 Скачать руководство пользователя | Manualshive

Страница: 31 / 55

background image

Kyland Technology (Shanghai) Co., Ltd PTS-DR200 Time Server

- 29 -

[Figure 3-18] Output Setting Screen (O1)

Table 17 – Output Setting (O1)

Items

Parameters

Description

Output

Signal

PPS1

IRIG-B1

PPM

PPH

Set output signal type for O1.

PPS1: Set output signal is PPS;
IRIG-B1: Set output signal is IRIG-B;
PPM: Set output signal is PPM;
PPH: Set output signal is PPH.

The PPS, PPM and PPH are pulse signal. The interval is per

second, per minute and per hour sending one pulse.

Second

Compensation

0s

Set second compensation offset for O1.
Unit is second(s);
Range is between -999999999s and 999999999s.
Default value is 0s.

When SO-PPS of SO is IRIG-B time signal, the parameter is

also valid for its output signal.

PPS

Compensation

0ns

Set PPS compensation offset for O1.
Unit is nanosecond(ns);
Range is between -250000000ns and 250000000ns.
Default value is 0ns.

When SO-PPS of SO is IRIG-B time signal, the parameter is

also valid for its output signal.

«
...
29
30
31
32
33
...
»

Содержание PTS-DR200
























































Отзывы:

Нет отзывов

Похожие инструкции для PTS-DR200

301269U - Ethernet Disk Mini Home Edition 500 GB Network Attached Storage Hard...

Бренд: LaCie Страницы: 74

Бренд: LOBENN Страницы: 86

Memory Bus Interface Type

Бренд: TDK Страницы: 1

KT-400 Expansion Module KT-MOD-INP16

Бренд: Kantech Страницы: 3

Бренд: AWB Страницы: 35

Бренд: PrimeArray Страницы: 208

Бренд: SMC Networks Страницы: 34

DiskStation DS410

Бренд: Synology Страницы: 2

SRN-64SEN-R Series

Бренд: Samsung Страницы: 2

PCLTA-10 PC LonTalk Adapter 73401

Бренд: Echelon Страницы: 2

WNA-100 - Bridge

Бренд: Xerox Страницы: 25

Бренд: Meinberg Страницы: 180

SharpSwitch PCIE-9205

Бренд: Artesyn Страницы: 102

Бренд: Sun Microsystems Страницы: 62

Бренд: RED SHIELD Страницы: 12

Бренд: Reeve Страницы: 35

Бренд: MaxTronic Страницы: 104

Бренд: METRObility Optical Systems Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды