KYLAND Technology PTS-DR200 Скачать руководство пользователя | Manualshive

Страница: 16 / 55

background image

Kyland Technology (Shanghai) Co., Ltd PTS-DR200 Time Server

- 14 -

Items

Parameters

Description

Status

Alarm

Normal: The time source has not bump data.
Alarm: The time source has bump data.

Source Priority

1~10

Show the priority for time source. 1 is highest source and 10 is
lowest source. It has 10 levels. System can select best time
sources by source priority.

Select ‘PTP’ in Source Channel, the screen will be shown as:

[Figure 3-8] Source Status Screen (PTP)

Table 8 – Source Status Information (PTP)

Items

Parameters

Description

Source Status

Normal

Alarm

Show the time source status.
Normal: The time source can use;
Alarm: The time source cannot use.

Source Bump

Status

Normal

Alarm

Show the time source bump status.
Normal: The time source has not bump data.
Alarm: The time source has bump data.

Source Priority

1~10

Show the priority for time source. 1 is highest source and 10 is
lowest source. It has 10 levels. System can select best time
sources by source priority.

3.4.3. Clock Status

Press ‘Clock Status’ on the left navigation bar to show clock status screen.
The clock status screen will be shown as:

«
...
14
15
16
17
18
...
»

Содержание PTS-DR200
























































Отзывы:

Нет отзывов

Похожие инструкции для PTS-DR200

Бренд: Abocom Страницы: 1

5big - Network NAS Server

Бренд: LaCie Страницы: 9

Бренд: LaCie Страницы: 14

Бренд: Supermicro Страницы: 27

Бренд: 3Com Страницы: 17

8STST4000PEXPSE

Бренд: StarTech.com Страницы: 10

Бренд: Supero Страницы: 130

InfiniteStorage 120

Бренд: Silicon Graphics Страницы: 42

Бренд: 3Com Страницы: 126

SmartPAC PRO 4353001

Бренд: Wintriss Страницы: 6

P400u - 32371 NAS 7200 RPM 160 GB Server

Бренд: Iomega Страницы: 2

33451 - StorCenter Pro NAS 400r/2TB Server

Бренд: Iomega Страницы: 2

33252 - NAS 300R SERIES 500GB

Бренд: Iomega Страницы: 24

DiskStation DS213

Бренд: Synology Страницы: 21

Бренд: Xerox Страницы: 244

Бренд: Paradyne Страницы: 50

Бренд: Patton electronics Страницы: 12

12000 - Series Chassis Modular Expansion Base

Бренд: Cisco Страницы: 132

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды