KYLAND Technology PTS-DR200 Скачать руководство пользователя | Manualshive

Страница: 18 / 55

background image

Kyland Technology (Shanghai) Co., Ltd PTS-DR200 Time Server

- 16 -

Press ‘Configuration’ to go to the configuration screen on the top of navigation bar.
The screen will be shown as:

[Figure 3-10] Configuration Screen

3.5.1. Sync Source Settings

Press ‘SYNC’ on the left navigation bar to show synchronization source setting screen.
Press ‘Source Channel’ to select SAT1/IRIG-B1/IRIG-B2/PTP channel.

  SAT1 source signal comes from ANT interface;
  IRIG-B1 source signal default comes from FI and also can be set to TI by manual;
  IRIG-B2 source signal default comes from TI and also can be set to FI by manual;
  PTP source signal comes from ETH0 or ETH1 interface.

If select ‘SAT1’ in Source Channel, the setting screen will be shown as:

«
...
16
17
18
19
20
...
»

Содержание PTS-DR200
























































Отзывы:

Нет отзывов

Похожие инструкции для PTS-DR200

Бренд: Abocom Страницы: 1

Бренд: Black Box Страницы: 16

Бренд: Black Box Страницы: 25

Expansion Modules Cabinet KT-MOD-CAB

Бренд: Kantech Страницы: 2

301414U - d2 Network NAS Server

Бренд: LaCie Страницы: 56

Бренд: IBM Страницы: 16

ApplianceStor 70v2

Бренд: Rasilient Страницы: 28

Ethernet Expansion Card

Бренд: IBM Страницы: 9

Бренд: Rosewill Страницы: 3

PCIe LAN Card RC-401-Dual-EX

Бренд: Rosewill Страницы: 8

Бренд: Allied Telesis Страницы: 1

14S0165 - MarkNet N8050 Print Server

Бренд: Lexmark Страницы: 29

MagicLAN SWL-2200C

Бренд: Samsung Страницы: 82

Бренд: Addonics Technologies Страницы: 1

Ethernet Device Driver none

Бренд: Sun Microsystems Страницы: 36

StorageTek SG-XPCIE1FC-EM8-Z

Бренд: Sun Microsystems Страницы: 56

Interface Adapter

Бренд: Sun Microsystems Страницы: 66

StorEdge X6767A

Бренд: Sun Microsystems Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды